|
Content
|
Terminal
No.
|
Measuring
condition and I/O signal (ignition switch ON and engine
idling
Except cruise set light)
|
Clutch
switch
|
B32
|
|
•
|
Battery voltage
is present when the clutch pedal is released.
|
|
•
|
“0” volt is present when the clutch
pedal is depressed.
|
|
Cruise
set indicator light
|
A16
|
(Press
the main switch and drive the vehicle at 40 km/h (25 MPH)
or more.)
|
•
|
Battery
voltage is present when the set switch is turned to OFF.
|
|
•
|
“0” volt is present when the set switch
is turned to ON.
|
|
Cruise
indicator light
|
A15
|
|
•
|
Battery voltage
is present when the main switch is turned to OFF.
|
|
•
|
“0” volt is present when the main
switch is turned to ON.
|
|
Main power supply
|
VB (CONTROL
1)
VB (CONTROL 2)
|
B6
B5
|
|
•
|
Battery voltage
is present when the main power supply is turned to ON.
|
|
•
|
“0” volt is present when the main
power supply is turned to OFF.
|
|
Vehicle
speed signal
|
B27
|
Lift-up the vehicle until
all four wheels are raised off the ground, and then rotate any wheel
manually. Approx. “5 V” and “0 V” pulse
signals are alternately input to ECM.
|
SET/COAST
switch
|
C11
|
|
•
|
Battery voltage
is present when the cruise control command switch is turned to SET/COAST
position.
|
|
•
|
“0” volt is present when the cruise
control command switch is released.
|
|
RES/ACC
switch
|
C1
|
|
•
|
Battery voltage
is present when the cruise control command switch is turned to RES/ACC
position.
|
|
•
|
“0” volt is present when the cruise
control command switch is released.
|
|
Brake
switch 1
(Brake switch)
|
C9
|
|
•
|
Battery voltage
is present when the brake pedal is released.
|
|
•
|
“0” volt is present when the brake
pedal is depressed.
|
|
Brake
switch 2
(Stop light switch)
|
C8
|
|
•
|
Battery voltage
is present when the brake pedal is depressed.
|
|
•
|
“0” volt is present when the brake
pedal is released.
|
|
Cruise
control main switch
|
C7
|
|
•
|
Battery voltage
is present while the cruise control main switch is depressed or is
turned to ON.
|
|
•
|
“0” volt is present when the cruise
control main switch is turned to OFF.
|
|
Ground
|
GND (CONTROL
1)
GND (CONTROL 2)
|
D2
D1
|
—
|
Ignition
switch
|
D15
|
|
•
|
Battery voltage
is present with the ignition switch is turned to ON.
|
|
•
|
“0” volt is present when the ignition
switch is turned to OFF.
|
|
Neutral position switch (MT
model)
|
D9
|
|
•
|
Battery voltage
is present when the shift lever is in anywhere except neutral position.
|
|
•
|
“0” volt is present when the shift
lever is in neutral position.
|
|
Neutral
signal (AT model)
|
D9
|
|
•
|
“Approx.
5 V” voltage (4AT model) or battery voltage (5AT model)
is present when the shift lever is set in any position except “P” or “N”.
|
|
•
|
“0 V” voltage is present when the
shift lever is set in “P” or “N” position.
|
|
