SAAB WIS ONLINE

PRE-RELEASE

30 21 268 Window sealing compound

30 21 268 Window sealing compound


Specifications

Teroson Terodicht Elastic T241. Black. Window sealant based on synthetic resin-synthetic rubber. 310 ml cartridge.

Saab application

Suitable for re-sealing of rubber-embedded windscreens, rear and side windows.

Packaging

1

Transport

No restrictions apply when transporting this product.

Directives



Material safety data sheet


1. IDENTIFICATION OF THE SUBSTANCE/PREPARATION AND THE COMPANY/UNDERTAKING

Product name

Terodicht Elastik (T241)

Application

Window sealing compound

Manufacturer - supplier

Loctite Sweden AB

Automotive Aftermarket

P.O. Box 8823

SE-402 71 GÖTEBORG

Tel: +46 31 750 54 00



2. COMPOSITION/INFORMATION ON INGREDIENTS

Product contains: solvent, filler and synthetic rubber.

Ingredient

CAS-no.

Content (%)

Hazard symbol/R-phrases

Remarks

Solvent naphtha (petroleum), light

64742-95-6

5-10

R10 Xn;R65 Xi;R37 N;R51/53

Benzene < 0.1%



Key

FB/FH/FM = Hazard code for fire/health/environment

T+ = Very toxic

T = Toxic

C = Corrosive

Xn = Harmful

Xi = Irritant

V = Moderately harmful

IK = Not subject to labelling

E = Explosive

O = Oxidizing

F+ = Extremely flammable

F = Highly flammable

N = Dangerous for the environment



3. HAZARDS IDENTIFICATION

Extremely flammable. Do not spray toward open flame or incandescent material as the pressurized container may ignite. Exposure to a strong heat source may cause the aerosol to explode.

Adverse health effects

The product contains small quantities of solvents. Large scale work on large surfaces in confined, poorly-ventilated area can produce vapours in concentrations that may cause headaches, dizziness, nausea and irritation to the respiratory system. Prolonged skin contact may cause redness, irritation and dry skin. May cause eye irritation.

Adverse environmental effects

The product contains a substance that is harmful to aquatic organisms and may cause long-term adverse effects to the aquatic environment.



4. FIRST AID MEASURES

Inhalation

The person should rest in fresh air under supervision. In the event of discomfort, seek medical advice and take along this material safety data sheet.

Skin

Take off immediately all contaminated clothing, and wash the effected skin with soap and water.

Eyes

Rinse immediately with plenty of water for at least 15 minutes. Remove any contact lenses and keep the eyes wide open. If the irritation persists: Visit a hospital and present this material safety data sheet.

Ingestion

Rinse the mouth immediately and drink plenty of water, milk or cream. Keep the person under supervision. In case of discomfort, visit a hospital immediately and take along this material safety data sheet.



5. FIRE-FIGHTING MEASURES

Suitable extinguishing media

Use a carbon dioxide or powder extinguisher. If exposed to heat, cool containers with water and remove from the area of fire, if this is possible without entailing risk.

Special protective equipment for firefighters

In the event of firefighting, use respiratory equipment with an air supply.



6. SPILLAGE/ACCIDENTAL RELEASE MEASURES

Personal precautions

Ensure adequate ventilation. For personal protection equipment, refer to section 8.

Environmental precautions

Avoid release into drains, the environment and the aquatic environment.

Methods for cleaning up

Scrape up spillage or remove with absorbent material. For disposal considerations, see point 13.



7. HANDLING AND STORAGE

Advice for safe handling

Observe good chemical hygiene.

Technical measures

Use working methods that minimize contact.

Technical information

In case of unpleasant odours and work in confined areas, mechanical ventilation may be necessary.

Storage instructions

No special measures required.

Storage conditions

Keep in a cool place.



8. EXPOSURE CONTROLS/PERSONAL PROTECTION

Technical measures

Efficient ventilation must be provided. Limits must not be exceeded and the risk of breathing vapours must be minimized.



Chemical identity

Limit

Type

Comments

Ref.

Trimethylbenzene, all isomers

25ppm 120mg/m³

NGV

AFS 2000:3



Respiratory equipment

In case of insufficient ventilation: Use respiratory equipment with gas filter, type A2.

Hand protection

Risk of contact: Wear protective gloves. Refer to information from the manufacturer for suitable gloves. The fluid can permeate the gloves. Change gloves often.

Eye protection

If there is a risk of contact with eyes: Wear eye/face protection.

Skin protection

No special measures required.

Hygiene measures

Change soiled clothes.



9. PHYSICAL AND CHEMICAL PROPERTIES

Form/state

Paste

Odour

Aromatic

Colour

Black

Solubility in water

Insoluble

Relative density

1.50 g/cm 3

Flash point

45°C

Other information

Kinematic viscosity at 40°C: >7 mm²/s



10. STABILITY AND REACTIVITY

Stability

Stable at normal temperatures.

Conditions and material to avoid:

Heating.

Hazardous decomposition products

None at normal temperatures.



11. TOXICOLOGICAL INFORMATION

Inhalation

High concentrations of vapours may cause drowsiness and can give rise to headaches, tiredness, dizziness and nausea.

Skin

Prolonged exposure may cause redness, irritation and dryness.

Eyes

May irritate and produce redness and stinging.

Ingestion

May cause irritation and nausea.

Prolonged exposure

Frequent repeated inhalation of even low concentrations can produce irritation, tiredness and memory loss and with time permanent damage to the nervous system, including the brain.



12. ECOLOGICAL INFORMATION

Mobility

The product is insoluble in water and produces a sediment in aquatic environments. The product contains volatile organic compounds (VOC) that evaporate rapidly from all surfaces.

Degradability

Degradability of product unknown.

Ecotoxicity

The product contains a substance that is toxic to aquatic organisms and may cause long-term adverse effects to the aquatic environment.



13. DISPOSAL CONSIDERATIONS

Spilt product and waste should be disposed of in accordance with the regulations laid down by local authorities.

Surplus

Leave for controlled disposal, quoting EWC code 08 04 02.

Contaminated packaging

Treat contaminated packaging in the same way as surplus.



14. TRANSPORT INFORMATION

The product is not included in international regulations for the transport of hazardous goods (IMDG, ICAO/IATA, ADR/RID).

15. REGULATORY INFORMATION

Labelling

Based on the information provided by the manufacturer regarding the chemical composition of the product, the Danish Toxicology Centre has judged that the product is not incorporated by the regulations of the Swedish National Chemicals Inspectorate on labelling, etc.

National regulations

European Directives 67/548/EEC relating to dangerous substances and 88/379/EC relating to dangerous preparations (up to and including the 26th adaptation). The Swedish National Chemicals Inspectorate's regulations accompanying the regulations (KIFS 1994:12) on the classification and labelling of chemical products, KIFS 1997:5 and KIFS 1999:3 with amendments. The Swedish National Chemicals Inspectorate's Chemical Products and Biotechnical Organisms Regulations KIFS 1998:8, with amendments. Provisions of the Swedish National Board of Occupational Safety and Health on occupational exposure limits, AFS 2000:3. Ordinance on dangerous waste (1996:971 with amendments).



16. OTHER INFORMATION

The user must be given guidance as to appropriate working procedures and be acquainted with the contents of this material safety data sheet. The information contained in this safety data sheet is based on the information that was available at the time of preparation of this safety data sheet and is provided under the assumption that the product is used under the specified conditions and in accordance with the working methods specified on the packaging or in the relevant technical literature. All other use of this product, such as in conjunction with other products or in different processes, is undertaken at the risk of the user.

Issued

2000-11-16 by

DANISH TOXICOLOGY CENTRE

Kogle Allé 2

DK-2970 HØrsholm, Denmark.

Tel: +45 45 76 20 55

Fax: +45 45 76 24 55




PRE-RELEASE