PRE-RELEASE
Upholstery, backrest
| Upholstery, backrest |
| 1. |
Remove the front seat from the car, see
Front seat
.
Remove the seat side panels, see Seat side panel . |
|
| 2. |
Cut off the cable tie securing the plastic cover and remove the cover on the inner side of the seat, 1 screw.
|
|
| 3. |
Undo the straps holding the backrest upholstery at the bottom.
Unplug the connector under the seat. Cut the relevant binding tie. |
|
| 4. |
Release the bottom edge of the upholstery strips and feed the cables out through the hole.
|
|
| 5. |
Pull out the cardboard from the backrest upholstery.
|
|
| 6. |
Undo the rear of the backrest upholstery by releasing the upholstery strips along the sides and folding back.
|
|
| 7. |
Release the upholstery strips along the back edge of the backrest frame.
|
|
| 8. |
Remove the lumber support adjustment knob (use a large screwdriver to carefully prise it off).
|
|
| 9. |
Unhook the lower part of the upholstery strip and remove the 2 wire rods that hold the bottom edge of the backrest upholstery.
|
|
| 10. |
Remove the felt trim on the sides of the backrest joint by detaching the felt from the hooks in the Pullmaflex flexible netting.
|
|
| 11. |
Unplug the relevant connectors under the seat.
Cut the relevant binding tie. |
|
| 12. |
Detach the 4 upholstery hooks and the 2 hooks that hold the airbag module cover.
|
|
| 13. |
Detach the top 3 hooks which hold the backrest upholstery to the foam cushion.
|
|
| 14. |
Remove the head restraint.
|
|
| 15. |
Remove the head restraint guide sleeves by pressing the catch in from the front.
|
|||||||
| 16. |
Remove the seat upholstery.
|
|
| To fit |
| 1. |
Pull the backrest upholstery into place and fit to the foam cushion.
|
|||||||
| 2. |
Fit the top 3 hooks that hold the backrest upholstery to the foam cushion.
|
|
| 3. |
Refit the head restraint guide sleeves.
|
|||||||
| 4. |
Refit the head restraint.
|
|
| 5. |
Refit the 4 upholstery hooks. Fit the airbag module cover and its hooks.
|
|
| 6. |
Fit the upholstery to the foam cushion, and position the wiring harness and connector correctly.
|
|
| 7. |
Fit the upholstery to the fabric pockets on the backrest sides. Attach the felt trim to the hooks provided in the Pullmaflex flexible netting.
|
|
| 8. |
Refit the 2 wire rods that hold the bottom edge of the backrest upholstery and secure the plastic strips.
|
|
| 9. |
Replace the upholstery strips along the back edge of the backrest frame.
|
|
| 10. |
Refit the back of the backrest upholstery by replacing the upholstery strips along the sides.
|
|
| 11. |
Insert the cardboard in the backrest upholstery.
|
|
| 12. |
Feed the cables through the hole and refit the upholstery strips on the underside.
|
|
| 13. |
Fasten the straps on the bottom of the backrest upholstery under the seat cushion.
Plug in the connectors and fit a new cable tie. 
|
|
| 14. |
Refit the knob for the lumbar support adjustment.
|
|
| 15. |
Fit the plastic cover on the inside of the seat, 1 screw and a new cable tie (fit the cable tie so that the head is positioned downwards).
|
|
| 16. |
Fit the seat side panels, see
Seat side panel
.
Fit the front seat in the car, see Front seat . |
|
