PRE-RELEASE
Floor carpet, front, CV
| Floor carpet, front, CV |
| To remove |
| 1. |
Remove both front seats
.
|
|
| 2. |
Remove the floor console
.
|
|
| 3. |
Remove the air duct to the rear air vent.
|
|
| 4. |
Remove the bellows from the air ducts to the rear floor vent.
|
|
| 5. |
Detach the seats' connectors from the floor.
|
|
| 6. |
Unhook the hand brake cables.
|
|
| 7. |
Remove the gear lever housing
. Let the cables remain in place.
|
|
| 8. |
Remove the screws holding the floor console aluminium frame to the floor tunnel.
|
|
| 9. |
Remove the clips from the leads to the ignition switch.
|
|
| 10. |
Lift out the centre console aluminium frame with the complete handbrake unit.
|
|||||||
| 11. |
Remove the two lower console support legs.
|
|
| 12. |
Remove the yaw rate sensor.
|
|
| 13. |
Disconnect the ACM connector and ground cable.
|
|
| 14. |
Remove the ACM.
|
|
| 15. |
Remove the metal support from the exhaust tunnel under the heating and ventilation unit.
|
|
| 16. |
Remove the doors' scuff panels and the lower A-pillar side panels.
|
|
| 17. |
Cut the carpet along the marked arrows.
|
|
| 18. |
Free the carpet from the floor vents.
|
|
| 19. |
Lift up the carpet around the floor console mountings and screws.
|
|
| 20. |
Lift out the front carpet.
|
|
| To fit |
| 1. |
Lift in and position the front carpet.
|
|
| 2. |
Slide the carpet under the pedals and the fan housing.
|
|||||||
| 3. |
Fit the carpet over the guide pins and mountings. Manoeuvre the carpet over the air ducts and the seat connectors.
|
|
| 4. |
Align the front and rear carpets.
|
|
| 5. |
Tape the carpet underneath along the line of the edge using
30 04 785 Fabric-backed tape black
.
|
|
| 6. |
Fit the scuff plate and the A-pillars' lower side panels.
|
|
| 7. |
Fit the metal support on the exhaust tunnel under the heating and ventilation unit.
|
|
| 8. |
Fit the ACM.
Tightening torque: 10 Nm (7lbf ft) |
|
| 9. |
Reconnect and fit the ACM connector and ground cable.
|
|
| 10. |
Fit the yaw rate sensor.
|
|
| 11. |
Fit the two lower console support legs.
Tightening torque 32 Nm (24 lbf ft) |
|
| 12. |
Position the floor console and handbrake assembly and fit the screws holding the aluminium frame to the floor tunnel.
|
|
| 13. |
Fit the clips for the wiring harness to the ignition switch.
|
|
| 14. |
Fit the gear lever housing
.
|
|
| 15. |
Attach the handbrake cables.
|
|
| 16. |
Fit the seats' connectors.
|
|
| 17. |
Fit the bellows to the air ducts for the rear floor vents.
|
|
| 18. |
Fit the air ducts to the rear floor vents.
|
|
| 19. |
Fit the floor console
.
|
|
| 20. |
Fit the front seats
.
|
|
