PRE-RELEASE
Generator, B207
| Generator, B207 |
| To remove |
| 1. |
Remove the battery cover and disconnect the negative battery cable.
|
|
| 2. |
Raise the car.
|
|
| 3. |
Remove the lower engine cover.
|
|
| 4. |
Place a receptacle under the car, connect a hose to the radiator and drain the coolant.
|
|
| 5. |
Remove the plastic nuts from the wheel arch liner.
|
|
| 6. |
Move aside the wheel arch liner, unload the belt tensioner and take off the belt (mark the belt direction). Use
83 96 095 Unloading tool, belt circuit B207E/L
.
|
|
| 7. |
Lower the car.
|
|
| 8. |
Remove the upper engine cover.
|
|
| 9. |
Unplug the connectors from the engine control module.
|
|
| 10. |
Remove the engine control module.
|
|
| 11. |
Detach the air hose from the air filter housing.
|
|
| 12. |
Remove the cover of the air filter housing.
|
|
| 13. |
Remove the air filter.
|
|
| 14. |
Unplug the connector from the pressure sensor.
|
|
| 15. |
Detach the intake air pipe from the air filter housing and lift up the filter housing.
|
|
| 16. |
Detach the coolant hose from the engine and radiator. Bend it aside.
|
|
| 17. |
Detach the vent hose from the air hose to the throttle body and loosen the fastener in the camshaft cover.
|
|
| 18. |
Bend aside the vent hose.
|
|
| 19. |
Detach the generator connections.
|
|
| 20. |
Remove the generator retaining bolts.
|
|
| 21. |
Lift up the generator; see illustration.
|
|
| To fit |
| 1. |
Position the generator correctly; see illustration.
|
|
| 2. |
Fit the generator retaining bolts.
Tightening torque 24 Nm (18 lbf ft) |
|
| 3. |
Attach the generator connections.
|
|
| 4. |
Fit the vent hose fastener to the camshaft cover.
|
|
| 5. |
Fit the vent hose to the throttle body air hose.
|
|
| 6. |
Fit the coolant hose to the engine and radiator.
|
|
| 7. |
Fit the intake air pipe to the air filter housing.
|
|
| 8. |
Plug in the connector to the pressure sensor.
|
|
| 9. |
Put the air filter in place.
|
|
| 10. |
Fit the air filter housing cover.
|
|
| 11. |
Fit the air hose to the air filter housing.
|
|
| 12. |
Fit the engine control module.
|
|
| 13. |
Plug in the engine control module connectors.
|
|
| 14. |
Fit the upper engine cover.
|
|
| 15. |
Raise the car.
|
|
| 16. |
Move aside the wheel arch liner and unload the belt tensioner. Use
83 96 095 Unloading tool, belt circuit B207E/L
and fit the belt (be certain it is fitted in the correct direction)
|
|
| 17. |
Fit the plastic nuts on the wheel arch liner.
|
|
| 18. |
Fit the lower engine cover.
|
|
| 19. |
Lower the car.
|
|
| 20. |
Connect the negative cable of the battery.
|
|
| 21. |
Fit the battery cover.
|
|
| 22. |
Reset the car; see
Procedures after battery disconnection
.
|
|
| 23. |
Top up with coolant and bleed the cooling system following
Bleeding the cooling system
.
|
|
| 24. |
When changing: Check battery, see
Battery check
and charge battery if necessary, see "Charging the battery."
|
|
