Body dimensions, 4D, 5D
The following measurements can be used to determine whether the car should be mounted in an alignment jig. Detailed measurements can be obtained from the alignment jig manufacturer.
Illustration A shows the correct direction for the measurements
Illustration B shows the incorrect direction for the measurements
|
Pos
|
Dimension, mm
|
Measuring points
|
|
1
|
4414
|
Total length Bumper member - Rear bumper abutment
|
|
2
|
1340
|
Hole in outer mounting of headlamp frame (*) - Hole in outer mounting of headlamp frame (*)
|
|
3
|
1315
|
Hole in outer mounting of headlamp frame (*) - Hole in front spring strut mounting (*)
|
|
4
|
457
|
Hole in outer mounting of headlamp frame (*) - Hole in front spring strut mounting (*)
|
|
5
|
1145
|
Hole in front spring strut mounting (*) - Hole in front spring strut mounting (*)
|
|
6
|
1568
|
Hole in outer mounting for headlamps (*) - Lower bonnet hinge mounting, centre of bolt head
|
|
7
|
1431
|
Lower bonnet hinge mounting, centre of bolt head centre of bolt head
|
|
8
|
1473
|
Distance between flanges for sealing strips on top edge of sill
|
|
9
|
1475
|
Distance between flanges for sealing strips on top edge of sill
|
|
10
|
1447
|
Lower A-pillar section in the corner near the windscreen member/A-pillar upper section, inner radius where the dimension is largest. diagonal
|
(*) = centre of hole is starting point of measurement.
|
Body measurements, rear, 4D
|
|
Pos
|
Dimension, mm
|
Measuring points
|
|
11
|
1153
|
Distance between corners towards rear lamp
|
|
12
|
699
|
Corner towards the rear light - Corner of the opening for the striking plate
|
(*) = centre of hole is starting point of measurement.
|
Body measurements, rear, 5D
|
|
Pos
|
Dimension, mm
|
Measuring points
|
|
13
|
1357
|
Stud, frame member - Outer hole for tailgate hinge (*)
|
|
14
|
859
|
Outer edge of square clip hole - Edge of rear roof member
|
|
15
|
1154
|
Distance between lower hole in luggage compartment aperture (*)
|
|
16
|
1421
|
Distance between hole for lamp mounting (*)
|
|
17
|
1214
|
Distance between hole for lamp mounting (*)
|
(*) = centre of hole is starting point of measurement.
|
Pos
|
Dimension, mm
|
Measuring points
|
|
18
|
989
|
Front hinge, rear upper hole (*) - Rear hinge, front lower hole (*)
|
|
19
|
1055
|
Front hinge, rear lower hole (*) - Rear hinge, front upper hole (*)
|
|
20
|
860
|
Rear hinge, front upper hole (*) - Striking plate upper hole (*)
|
|
21
|
942
|
Rear hinge, front lower hole (*) - Striking plate upper hole (*)
|
(*) = centre of hole is starting point of measurement.
|
Body measurements, B-pillar, 4D, 5D
|
|
Pos
|
Dimension, mm
|
Measuring points
|
|
22
|
1599
|
Depression in inner sill edge - Bolt hole for seat belt anchorage (*). Diagonal measurement
|
|
23
|
1416
|
Distance between upper edge of rear clip hole (*)
|
(*) = centre of hole is starting point of measurement.
|
Pos
|
Dimension, mm
|
Measuring points
|
|
24
|
1346
|
Front mounting of subframe, centre of bolt head LH side - Hole in floor reinforcement RH side (*)
|
|
25
|
1350
|
Front mounting of subframe, centre of bolt head RH side - Hole in floor reinforcement LH side (*)
|
|
26
|
1475
|
Distance between inside of sill edge
|
|
27
|
1475
|
Distance between inside of sill edge
|
|
28
|
1838
|
Hole in member LH side (*) - Hole for towbar mounting RH side (*)
|
|
29
|
1822
|
Hole in member RH side (*) - Hole for towbar mounting LH side (*)
|
(*) = centre of hole is starting point of measurement.
