Front exhaust system with catalytic converter, 4-cyl. B205E
|
|
Front exhaust system with catalytic converter, 4-cyl. B205E
|
|
1.
|
Remove the bypass pipe and valve (C).
|
Note
|
|
There is an O-ring at the bypass pipe's attachment to the turbo intake pipe.
|
|
|
2.
|
Remove the exhaust manifold heat shield (B).
|
|
3.
|
Remove the oxygen sensor (A).
|
|
4.
|
Undo the two upper nuts securing the joint between the turbocharger and front exhaust system (D).
|
|
6.
|
Remove the lower front cover (A).
|
|
7.
|
Undo the third nut holding the turbocharger and front exhaust system (E) together.
|
|
8.
|
Undo the pipe joint between the front and rear exhaust systems (C).
|
|
9.
|
Remove the clips from the rubber mountings (B).
|
|
10.
|
Carefully withdraw the rubber mountings (A).
|
|
11.
|
Lower the front exhaust system.
|
Important
|
|
The flexible section at the front of the exhaust system should not be bent out of line by more than 7°, i.e. if the front exhaust system is allowed to hang, it must not bend more than the sag caused by its own weight.
|
|
If the pipe is overloaded, permanent deformation of the components will result. This can cause noise and leakage, and damage at a later stage.
|
|
|
|
|
Note
|
|
Coat the studs sparingly with Molycote 1000, part no. 30 20 971 or similar.
|
|
Important
|
|
The flexible section at the front of the exhaust system should not be bent out of line by more than 7°, i.e. if the front exhaust system is allowed to hang, it must not bend more than the sag caused by its own weight.
|
|
If the pipe is overloaded, permanent deformation of the components will result. This can cause noise and leakage, and damage at a later stage.
|
|
|
|
1.
|
Raise the front part of the exhaust system.
|
|
2.
|
Fit the third nut holding the turbocharger and front exhaust system (E) together.
|
|
3.
|
Fit the rubber mountings (A).
|
|
4.
|
Fit the clips on the rubber mountings (B).
|
|
5.
|
Fit the pipe joint between the front and rear exhaust systems and fit the nuts (C).
|
|
6.
|
Fit the two upper nuts securing the joint between the turbocharger and front exhaust system (D).
|
Important
|
|
When fitting the front exhaust system to the turbo, the nuts should be tightened alternately to avoid distorting the flange. The flange must not abut against the turbo connection flange.
|
|
Ensure that the system hangs straight so that no stresses occur during fitting.
|
|
|
|
|
7.
|
Tighten the nuts to the prescribe tightening torque:
Turbo/front exhaust pipe: 24 Nm (17.7 lbf ft)
Front/rear exhaust system: 22 Nm (16.2 lbf ft)
Bypass pipe/intake pipe: 8 Nm (5.9 lbf ft)
Bypass pipe, hose clip: 8 Nm (5.9 lbf ft)
|
|
8.
|
Fit the lower front cover (A).
|
|
9.
|
Fit the oxygen sensor (A).
Tightening torque, oxygen sensor 55 Nm (40.5 lbf ft)
|
|
10.
|
Fit the exhaust manifold heat shield (B).
|
Note
|
|
There is an O-ring at the bypass pipe's attachment to the turbo intake pipe.
|
|
|
11.
|
Fit the bypass pipe and valve (C).
|
