PRE-RELEASE
Test readings, control module connections
| Test readings, control module connections |
| Scope |
The following pages contain specified values and directions for measuring signals and levels on the automatic transmission control module.
| Points to remember: |
| • |
Observe the test conditions, use your common sense when judging the readings obtained.
|
|
| • |
The specified values are with the ignition in position ON unless stated otherwise.
|
|
| • |
First check that the control module is supplied with current and grounded.
|
|
| • |
Then check all sensor inputs and signals from other systems.
|
|
| • |
Finally, check the control module inputs. Remember that the test readings do not indicate whether or not the actuator is in working order.
|
|
| • |
If any reading is not OK, consult the wiring diagram to trace the leads, connectors or components which ought to be checked more thoroughly.
|
|
| • |
The specified test readings refer to those obtained with a calibrated Fluke 88/97.
|
|
| • |
Test readings %(+) and ms(+) indicate the signal's pulse ratio and pulse duration. A test instrument capable of measuring pulse ratio and pulse width must be used. The sign denotes a positive trigger pulse, TRIG+.
|
|
| Table connector A |
|
Pin, connector
A
|
Cable colour
|
Component/ Function
|
In/Out
|
Test conditions
|
Test between
|
Test reading
|
See
|
|
1
|
no connection
|
||||||
|
2
|
no connection
|
||||||
|
3
|
no connection
|
||||||
|
4
|
no connection
|
||||||
|
5
|
no connection
|
||||||
|
6
|
no connection
|
||||||
|
7
|
OG/WH
|
WINTER mode connection
|
In
|
7-23
|
ON=B+
OFF=0 V |
||
|
8
|
Up and down gear changing
|
In
|
8 - 23
|
0 - 5V
|
|||
|
9
|
No connection
|
||||||
|
10
|
No connection
|
||||||
|
11
|
No connection
|
||||||
|
12
|
No connection
|
||||||
|
13
|
No connection
|
||||||
|
14
|
No connection
|
||||||
|
15
|
No connection
|
||||||
|
16
|
No connection
|
||||||
|
17
|
BU
|
Switch Sport
|
In
|
||||
|
18
|
No connection
|
||||||
|
19
|
No connection
|
||||||
|
20
|
No connection
|
||||||
|
21
|
No connection
|
||||||
|
22
|
RD/BU
|
Battery voltage (+15 circuit)
|
In
|
Ignition ON
|
|||
|
23
|
BK
|
Ground
|
|
|
|||
|
24
|
No connection
|
||||||
|
25
|
GN
|
Bus +
lead 1 |
in/out
|
|
|||
|
26
|
WH
|
Bus -
lead 1 |
in/out
|
|
|||
|
27
|
No connection
|
||||||
|
28
|
No connection
|
||||||
|
29
|
No connection
|
||||||
|
30
|
No connection
|
||||||
|
31
|
RD/BU
|
Battery voltage (+15 circuit)
|
In
|
Ignition ON
|
|||
|
32
|
BK
|
Ground
|
|||||
|
33
|
RD
|
Battery voltage (+30 circuit)
|
In
|
||||
|
34
|
No connection
|
||||||
|
35
|
No connection
|
|
|
||||
|
36
|
No connection
|
|
|||||
|
37
|
No connection
|
||||||
|
38
|
No connection
|
*A vehicle speed reading can be obtained with the diagnostics instrument, command menu "Read functions" and "Output speed”.
Table connector B
|
Pin, connector
B
|
Cable colour
|
Component/ Function
|
In/Out
|
Test conditions
|
Test between
|
Test reading
|
See
|
|
1
|
no connection
|
||||||
|
2
|
no connection
|
||||||
|
3
|
no connection
|
||||||
|
4
|
no connection
|
||||||
|
5
|
no connection
|
||||||
|
6
|
BN/WA
|
Gear selector, position A
|
In
|
Ignition ON
The signal is grounded in positions P, R, and M |
6 - 23
|
Selector lever position P, R, M: 0-0.5V
Other positions: 0-2V |
|
|
7
|
OG/WH
|
Gear selector, position C
|
In
|
Ignition ON
The signal is grounded in positions D, M, and L |
7-23
|
Selector lever position: D, M, L: 0-0.5V
|
|
|
8
|
BU/WH
|
Solenoid S3
|
Out
|
A voltage is present at the solenoid when it is activated by the TCM in gears 1, 2, and 3
|
Signal activated: 0-2V
Not activated: Low |
||
|
9
|
No connection
|
||||||
|
10
|
No connection
|
||||||
|
11
|
No connection
|
||||||
|
12
|
BK/WH
|
Solenoid Lock-Up, SLU ground
|
In
|
Signal = Low
|
|||
|
13
|
GN/WH
|
Solenoid S5
|
Out
|
Ignition ON
A voltage is present at the solenoid when it is activated by the TCM in position R and when changing from 2 to 3 |
Activated: 0-2V
Not activated=Low |
||
|
14
|
GN/WH
|
Solenoid S4
|
Out
|
Ignition ON
A voltage is present at the solenoid when it is activated by the TCM in gears 3, 4, and 5 |
Activated: 0-2V
Not activated=Low |
||
|
15
|
BK/WH
|
Solenoid System pressure, SLT ground
|
In
|
Signal = Low
|
|||
|
16
|
VT
|
Gear selector, position B
|
In
|
Ignition ON
The signal is grounded in positions R, N, D, M |
16 - 23
|
Selector lever position R, N, D, M: 0-0.5V
Other positions: 0-2V |
|
|
17
|
GY
|
Gear selector, position PA
|
In
|
Ignition ON
The signal is grounded in positions P, N, M, and L |
17 - 23
|
Selector lever position P, N, M, L: 0-0.5V
Other positions: 0-2V |
|
|
18
|
No connection
|
||||||
|
19
|
No connection
|
||||||
|
20
|
No connection
|
||||||
|
21
|
GN
|
Oil temp. sensor +
|
Out
|
The voltage decreases with increasing temperature
|
Cold transmission (+20°C): 3.4V ±10%
Warm transmission (100°C): 0.7V ± 10% |
||
|
22
|
WH/PK
|
Sensor input speed signal
|
In
|
When the toothed wheel rotates the sensor generates a square wave signal. The frequency increases with speed.
|
Tooth aligned with sensor: 14mA
Gap aligned with sensor: 7mA |
||
|
23
|
PK
|
Sensor output speed signal
|
In
|
When the toothed wheel rotates the sensor generates a square wave signal. The frequency increases with speed.
|
Tooth aligned with sensor: 14mA
Gap aligned with sensor: 7mA |
||
|
24
|
BU/WH
|
Solenoid S2
|
Out
|
Ignition ON
A voltage is present at the solenoid when it is activated by the TCM in gears 1 and 5 |
Activated: 0-2V
Not activated = Low |
||
|
25
|
BU/WH
|
Solenoid Lock-Up, SLU +
|
Out
|
A voltage is present at the solenoid when it is activated by the TCM
|
PWM=300 Hz. The frequency is independent of the driving conditions. It is the duty cycle of the signal which changes during control of the system pressure.
|
||
|
26
|
BU/WH
|
Solenoid system pressure clutch SLS +
|
Out
|
A voltage is present at the solenoid when it is activated by the TCM
|
PWM=300 Hz. The frequency is independent of the driving conditions. It is the duty cycle of the signal which changes during control of the system pressure.
|
||
|
27
|
No connection
|
||||||
|
28
|
No connection
|
||||||
|
29
|
No connection
|
||||||
|
30
|
No connection
|
||||||
|
31
|
WH/PK
|
Oil temp. sensor, ground
|
In
|
Signal = Low
|
|||
|
32
|
WH
|
Sensor input speed, voltage measurement
|
In
|
|
Signal = B+
|
||
|
33
|
RD/GN
|
Sensor output speed, voltage measurement
|
In
|
|
Signal = B+
|
||
|
34
|
GN/WH
|
Solenoid S1
|
Out
|
Ignition ON
A voltage is present at the solenoid when it is activated by the TCM in gear 1 |
Activated: 0-2V
Not activated: Low |
||
|
35
|
BU/WH
|
Solenoid system pressure SLT +
|
Out
|
A voltage is present at the solenoid when it is activated by the TCM
|
PWM=300 Hz. The frequency is independent of the driving conditions. It is the duty cycle of the signal which changes during control of the system pressure.
|
||
|
36
|
BK/WH
|
Solenoid system pressure clutch SLS ground
|
In
|
Signal = Low
|
|||
|
37
|
No connection
|
||||||
|
38
|
No connection
|
