(385-2647) Fitting the seals in the SPA connector
Symptom: SID message "PARK.ASSIST FAILURE".
|
MODIFICATION INSTRUCTION
|
|
Bulletin Nbr:
|
385-2647
|
|
Date:
...........
|
Januari 2007
|
|
Market:
|
enligt sep. lista
|
|
|
Fitting the seals in the SPA connector
|
Cars in stock must be rectified before delivery.
Cars already delivered must be rectified in connection with a scheduled visit to the garage for service or repairs.
Saab 9-5 M06-07 within Vehicle Identification Number range 63519935 - 73504857 equipped with SPA.
|
Note
|
|
Some cars within the Vehicle Identification Number range are not affected. See separate information for the Vehicle Identification Numbers affected.
|
Due to a specification error there are no seals on the cables in the connector housing adjacent to the bumper in cars equipped with SPA.
Symptom description
SID message "PARK.ASSIST FAILURE".
127 897 94 Cable terminals (6 per car).
16-302 38 92 (ej US/CA) Seals (sufficient for 4 cars).
302 38 92 (US/CA) Seals (sufficient for 4 cars).
55 44 556 Connector housing, the connector housing must only be replaced if it breaks.
Contact 61, Contact Protect CRC (www.crcindustries.com) or similar.
For fitting the modification identity plate (not US/CA):
12 785 148 Modification identity plate
93 160 907 Cleaning agent Motip Dupli, aerosol 400 ml (sufficient for 50-100 cars)
|
Checking the modification identity plate (not US/CA)
|
Before proceeding, check box A1 of the modification identity plate. From and including M04 the car's Warranty and Service Book contains the "Table of Modifications". A modification identity plate must be fitted in accordance with the section "Fitting the modification identity plate" where local directives require the marking of the car. If the box is not marked, continue as follows.
|
1.
|
Turn the ignition key to the OFF position.
|
|
2.
|
Remove the screws (A) in the left-hand rear wheel housing and pull out the casing (B).
|
|
3.
|
Clean the connector housing H6-1, unplug the connector and pull it out.
|
|
4.
|
Insert a plastic wedge between the lamp and the bumper.
|
|
5.
|
Clean the connector housing H6-1.
|
|
6.
|
Mark the cables with the connector housing's (H6-1) position number and prise out the cable terminals. Use the extraction tool from the kit 85 80 151.
|
|
7.
|
Cut the cable terminals away from the wiring harness. Cut as close to the cable terminals as possible.
|
|
8.
|
Fit the seals and cable terminals:
For instructions on repairing the wiring harness, see WIS - Electrical system - Wiring harness - Adjustment/Replacement.
- Guide the seals (16- 302 38 92) up, with the thick section first, slightly above the cable insulation.
- Fit new cable terminals (127 897 94). Use the green pliers (86 12 038).
- Guide the thin section of the seal down over the cable terminal and the wire strands. The thick section of the seal must be fitted over the upper section of the cable terminal and the cable insulation.
|
|
9.
|
Fit the cable terminals, according to marked position numbers, in connector housing H6-1.
Check that the cable terminals lock and the seals are firmly in contact with the connector housing.
|
|
10.
|
As required:
Clean the pins in the bumper's connector housing from corrosion, use Contact 61.
|
|
11.
|
Spray the contact surfaces in connector housing H6-1 using Contact 61 and plug it in.
|
|
12.
|
5D:
Remove the plastic wedge.
|
|
13.
|
Insert the casing (A) fit the screws (B).
|
|
14.
|
Carry out a check of SPA function:
- Turn the ignition key to the ON position.
- Engage reverse gear.
- Check that the message "PARK.ASSIST FAILURE" is not shown in the SID.
|
|
Marking the modification identity plate (not US/CA)
|
After carrying out the procedure, mark box A1 on the modification identity plate. From and including M04 the car's Warranty and Service Book contains the "Table of Modifications". Mark the box with the number "7" if the procedure was carried out by the importer or with the number "8" if carried out by the dealer.
|
Fitting the modification identity plate (not US/CA)
|
|
Note
|
|
A modification identity plate must only be fitted where local directives require the marking of the car.
|
Fit the modification identity plate in accordance with WIS
9-5 M04 - General - General - Technical data - Plates and labels
|
Warranty/Time Information
|
See separate information.
