SAAB WIS ONLINE

PRE-RELEASE

Roof console, 5D

Roof console, 5D

To remove

Warning

Take care not to damage or loosen the energy absorbers. Damaged or loose energy absorbers must not be refitted. If the occasion should arise, the entire headlining must be changed. Damaged energy absorbers may impair head protection in case of a collision.



1. Remove the sun visors and their mountings (A).


2. Remove the light lens from the cover (B) by carefully prizing with a screwdriver in the clip recess of the light lens.

Note

Exercise care, as the light lens could crack if incorrectly removed.

Take care not to scratch the cover.


3. Unscrew the roof console's cover (B).

4. Unplug any connectors for microphone and interior temperature sensor and lift away the cover (B).

5. Remove the interior rearview mirror, 3 screws (C).

6. Unplug and separate the grey 10-pin connector.

7. Remove the A-pillar trims (fastened with clips) (D).

8. Remove all courtesy handles above the doors (E).

9. Cars with sunroof: Undo the clips (A) in the rear edge of the sunroof (x 3) by carefully pressing with a finger from the rear.


10. Undo the B-pillar trims (A), fastened with clips. Lift the trims from the air ducts and place them to one side.


11. Remove the rear roof covering (A), fastened with clips. Unplug and separate the connectors for the glass breakage sensor and luggage compartment lighting.


12. Undo the D-pillar trims (B).

13. Remove the roof coverings (C) between the C and D-pillars.

14. Detach the top of the C-pillar trims (D), fastened with clips.

15. Remove the cargo safety net mountings (E). Remove the covers and undo the clips.

16. Undo the clips (F) securing the rear of the headlining (x 2) by turning them 90° and pulling them down.

17. Carefully pull the headlining out of the door weatherstrips on the passenger side. Then pull the headlining out of the door weatherstrips.

18. Cars with sunroof: Detach the headlining from the hooks adjacent to the sunroof.

19. Unplug and separate the connector on the upper surface of the headlining.

20. Carefully lower the headlining.

21. Remove the roof console (A).


22. Unplug and separate the connector (B) and unplug the connector for the sunroof (C) if fitted.

Important

Be careful not to bend the roof.



To fit

Warning

Take care not to damage or loosen the energy absorbers. Damaged or loose energy absorbers must not be refitted. If the occasion should arise, the entire headlining must be changed. Damaged energy absorbers may impair head protection in case of a collision.



1. Plug in the connector (B) and also (C) if such a connector is fitted.


Important

Be careful not to bend the roof.


2. Fit the roof console (A).

3. Plug in the grey 10-pin connector.

4. Carefully lift the headlining into place.

5. Plug in the connector on the upper surface of the headlining.

6. Position the headlining in front of the roof console.

7. Cars with sunroof: Hook the headlining into the hooks adjacent to the sunroof.

8. Position the headlining against the door weatherstrips.

9. Fit the clips (F) which hold the headlining at the rear edge.


10. Fit the D-pillar trims (B).

11. Plug in the connector for the glass breakage sensor and luggage compartment lighting. Fit the rear roof covering (A).

12. Fit the cargo safety net mountings (E) and the covers.

13. Fit the C-pillar trims (D).

14. Fit the roof coverings (C) between the C and D-pillars.

15. Fit the B-pillar trims (A).


16. Cars with sunroof: Secure the clips (A) in the rear edge of the sunroof.


17. Fit all courtesy handles above the doors (E).


18. Fit the A-pillar trims (D).

19. Fit the interior rearview mirror (C).

20. Fit the roof console's cover (B), and carefully press the light lens into place.

21. Plug in the connectors for the mirror lighting in the sun visors. Fit the brackets for the sun visors, as well as the sun visors (A).


PRE-RELEASE