DTC P2300, P2301, P2303, P2304, P2306, P2307, P2309, or P2310 (LDK with Turbocharger)

/ 9-5 (9650) / 2010 / 2. Engine / Engine management and fuel system, 4-cyl petrol / Fault diagnosis, diagnostic trouble codes / DTC P2300, P2301, P2303, P2304, P2306, P2307, P2309, or P2310 (LDK with Turbocharger)

Diagnostic Instructions

•	Perform the Diagnostic System Check - Vehicle prior to using this diagnostic procedure.

•	Review Strategy Based Diagnosis for an overview of the diagnostic approach.

•	Diagnostic Procedure Instructions provides an overview of each diagnostic category.

DTC Descriptors

DTC P2300

Ignition Coil 1 Control Circuit Low Voltage

DTC P2301

Ignition Coil 1 Control Circuit High Voltage

DTC P2303

Ignition Coil 2 Control Circuit Low Voltage

DTC P2304

Ignition Coil 2 Control Circuit High Voltage

DTC P2306

Ignition Coil 3 Control Circuit Low Voltage

DTC P2307

Ignition Coil 3 Control Circuit High Voltage

DTC P2309

Ignition Coil 4 Control Circuit Low Voltage

DTC P2310

Ignition Coil 4 Control Circuit High Voltage

Diagnostic Fault Information

Circuit	Short to Ground	High Resistance	Open	Short to Voltage
Ignition Coil 1 Control Circuit	P2300	P0351	P0351	P2301
Ignition Coil 2 Control Circuit	P2303	P0352	P0352	P2304
Ignition Coil 3 Control Circuit	P2306	P0353	P0353	P2307
Ignition Coil 4 Control Circuit	P2309	P0354	P0354	P2310

Circuit/System Description

The ignition system uses individual ignition coil/module assemblies for each cylinder. The engine control module (ECM) controls the individual coils by transmitting timing pulses on the ignition control (IC) circuit of each ignition coil/module to enable a spark event. When the engine is running the ECM monitors each IC circuit for improper voltage levels. Each ignition coil/module has the following circuits:

•	Ignition voltage

•

Ground

•

IC

•	Low Reference

Conditions for Running the DTCs

•	The engine speed is less than 6,000 RPM.

•	The ignition 1 voltage signal is between 9-18 V.

•	DTCs P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310 run continuously when the above conditions are met.

Conditions for Setting the DTCs

•	The ECM detects a short to ground on the circuit or the ignition coil/module for greater than 4 seconds continuously or 50 seconds cumulative. OR

•	The ECM detects a short to voltage on the circuit or the ignition coil/module for greater than 4 seconds continuously or 50 seconds cumulative.

Action Taken When the DTC Sets

DTCs P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310 are Type B DTCs.

Conditions for Clearing the MIL/DTC

DTCs P2300, P2301, P2303, P2304, P2306, P2307, P2309, P2310 are Type B DTCs.

Reference Information

Schematic Reference

Engine Controls Schematics

Connector End View Reference

Component Connector End Views

Electrical Information Reference

•	Circuit Testing

•	Connector Repairs

•	Testing for Intermittent Conditions and Poor Connections

•	Wiring Repairs

DTC Type Reference

Powertrain Diagnostic Trouble Code (DTC) Type Definitions

Scan Tool Reference

Control Module References for scan tool information

Circuit/System Verification

1.	Start and run the engine.

2.	Observe the scan tool Misfire Current Cylinder parameters. The counters should not be incrementing.

3.	Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.

Circuit/System Testing

1.	Turn ON the ignition, with the engine OFF.

2.	Test the affected ignition control circuit terminal C for a short to ground or for a short to voltage.

3.	If a fault is found, repair the circuit as needed.

4.	Ignition OFF, exchange the affected T8 ignition coil/module with the T8 ignition/coil module of a good cylinder.

5.	Start the engine and observe the scan tool.

6.	If the DTC or the misfire transfers with the suspect ignition/coil module, replace as needed.

7.	If the DTC or the misfire does not transfer with the suspect T8 ignition/coil module, replace the K20 ECM.

Repair Instructions

•	Ignition Coil Replacement

•	Control Module References for ECM replacement, setup, and programming

Repair Verification

If the customer concern was a flashing MIL, then perform the following procedure:

1.	Install any components that have been removed or replaced during diagnosis.

2.	Perform any adjustments, programming or setup procedures that are required when a component is removed or replaced.

3.	Clear the DTCs.

4.	Turn OFF the ignition for 60 seconds.

5.

If the repair was related to a DTC, duplicate the Conditions for Running the DTC and use the Freeze Frame/Failure Records, if applicable, in order to verify the DTC does not reset. If the DTC resets or another DTC is present, refer to the Diagnostic Trouble Code (DTC) List - Vehicle and perform the appropriate diagnostic procedure.

6.	To verify that the performance of the catalytic converter has not been affected by the condition that set this DTC, perform the Repair Verification for DTC P0420. Refer to DTC P0420 .

Our Friends