High Intensity Discharge Lamp Malfunction
|
|
High Intensity Discharge Lamp Malfunction
|
|
Diagnostic Fault Information
|
|
Circuit
|
Short to Ground
|
Open/High Resistance
|
Short to Voltage
|
Signal Performance
|
Relay Coil Control
|
2
|
1
|
1
|
-
|
Headlamp Low Beam Control
|
1
|
1
|
2
|
-
|
Low Beam Headlamp Ground
|
-
|
1
|
-
|
-
|
1. Low Beam Headlamps Inoperative
2. Low Beam Headlamps Always ON
|
|
Circuit/System Description
|
The vehicle headlamps are controlled by the body control module (BCM) based on inputs from the headlamp switch and the turn signal/multifunction switch. The headlamp switch has four positions: OFF, AUTOMATIC LIGHT, PARKING LIGHT, and LOW BEAM. The default headlamp switch position is AUTOMATIC LIGHT, in which the BCM uses the ambient light sensor to determine when headlamps are needed. The OFF portion of the headlamp switch is a momentary switch which overrides the automatic headlamp and will turn OFF the vehicle headlamps. When in the OFF position, the headlamp switch grounds the headlamp switch headlamps OFF signal circuit, prompting the BCM to turn OFF the headlamps. The Park position of the headlamp switch will only illuminate the vehicle parking lamps. The LOW BEAM position of the headlamp switch will illuminate both the parking lamps, as well has the headlamps. With the headlamp switch in the LOW BEAM position, the headlamp switch headlamps on signal circuit is grounded, prompting the BCM to turn on the headlamps, regardless of other factors such as ambient light.
When a low beam request is received, the BCM grounds the headlamp low beam relay control circuit. This energizes the coil in the headlamp low beam relay, causing the relay switch to close. This then applies B+ to both low beam high intensity discharge (HID) headlamps through the left low beam and right low beam fuses, illuminating the low beam headlamps. When a high beam request is received, the BCM grounds the headlamp high beam relay control circuit. This energizes the coil in the high beam relay, causing the relay switch to close. This then applies B+ to both low beam HID headlamps through the left high beam and right high beam fuses, illuminating the high beam headlamps.
|
•
|
Flickering light, caused in the early stages of bulb failure.
|
|
•
|
Lights go out, caused when the ballast detects excessive, repetitive bulb restrike.
|
|
•
|
Color change, the lamp may change to a dim pink glow.
|
Schematic Reference
Headlights/Daytime Running Lights (DRL) Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References
for information on diagnostic tools
Warning
|
|
The high intensity discharge system produces high voltage and current. To reduce the risk of severe shocks and burns:
|
|
•
|
Never open the high intensity discharge system ballast or the arc tube assembly starter.
|
|
•
|
Never probe between the high intensity discharge system ballast output connector and the arc tube assembly.
|
|
|
|
|
|
|
1.
|
Ignition OFF, disconnect the KR49 Headlamp Low Beam Relay.
|
|
2.
|
Ignition ON, verify that a test lamp does not illuminate between the control circuit terminal 87 and ground.
|
|
3.
|
If the test lamp illuminates, test the control circuit for a short to voltage.
|
|
4.
|
Verify that a test lamp illuminates between the B+ circuit terminal 86 and ground.
|
|
5.
|
If the test lamp does not illuminate, test the B+ circuit for a short to ground or an open/high resistance.
|
|
6.
|
Verify that a test lamp illuminates between the B+ circuit terminal 30 and ground.
|
|
7.
|
If the test lamp does not illuminate, test the B+ circuit for an open/high resistance.
|
|
8.
|
Disconnect the harness connector at the inoperative headlamp.
|
|
9.
|
Test for less than 5 Ω between the headlamp ground circuit terminal 10 and ground.
|
|
10.
|
If greater than the specified range, test the ground circuit for an open/high resistance.
|
|
11.
|
Connect the harness connector at the headlamp.
|
|
12.
|
Connect a 10 A fused jumper wire between the B+ circuit terminal 30 and the control circuit terminal 87. Verify the headlamp is activated.
|
|
13.
|
If the headlamp does not activate and the jumper wire fuse is good, test the control circuit for an open/high resistance. If the circuit tests normal, test or replace the headlamp.
|
|
14.
|
If the headlamp does not activate and the jumper wire fuse is good, test the control circuit for an open/high resistance. If the circuit tests normal, test or replace the headlamp.
|
|
15.
|
Connect a test lamp between the B+ circuit terminal 86 and the control circuit terminal 85.
|
|
16.
|
Command the Low Beams ON and OFF with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
|
|
17.
|
If the test lamp is always ON, test the control circuit for a short to ground. If the circuit tests normal, replace the K9 Body Control Module.
|
|
18.
|
If the test lamp is always OFF, test the control circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.
|
|
19.
|
If all circuits test normal, test or replace the KR49 Headlamp Low Beam Relay.
|
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.
