PRE-RELEASE
DTC P0650
| DTC P0650 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptor |
DTC P0650
Malfunction Indicator Lamp (MIL) Control Circuit
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|
MIL Voltage Supply
|
P0650
|
P0650
|
-
|
-
|
|
MIL Control
|
P0650*
|
P0650
|
P0650
|
-
|
|
* The MIL remains ON
|
||||
| Circuit/System Description |
The malfunction indicator lamp (MIL) is located on the instrument panel cluster (IPC). The MIL informs the driver that an emission system fault has occurred and that the engine control system requires service. The engine control module (ECM) monitors the MIL control circuit for conditions that are incorrect for the commanded state of the MIL. For example, a failure condition exists if the ECM detects low voltage when the MIL is commanded OFF, or high voltage when the MIL is commanded ON.
| Conditions for Running the DTC |
| • |
The engine speed is more than 80 RPM.
|
|
| • |
The ignition voltage is between 10-18 V.
|
|
| • |
The ECM has commanded the MIL ON and OFF at least once during the ignition cycle.
|
|
| • |
DTC P0650 runs continuously when the above conditions are met.
|
|
| Conditions for Setting the DTC |
The ECM detects an open, a short to ground, or a short to voltage on the circuit that controls the MIL.
| Action Taken When the DTC Sets |
DTC P0650 is a Type B DTC.
| Conditions for Clearing the DTC |
DTC P0650 is a Type B DTC.
| Diagnostic Aids |
If the condition is intermittent, move the related harnesses and connectors with the engine operating. Monitor the scan tool Circuit Test Status parameters for the component. The Circuit Test Status parameter will change from OK or Not Run to Fault if there is a condition with the circuit or a connection.
| Reference Information |
Schematic Reference
| • |
Engine Controls Schematics
|
|
| • |
Instrument Cluster Schematics
|
|
Connector End View Reference
Component Connector End Views
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information.
| Circuit/System Verification |
| 1. |
Ignition ON, command the MIL ON and OFF with a scan tool. The MIL should turn ON and OFF as commanded.
|
|
| 2. |
Ignition ON, observe each of the MIL Control Circuit Test parameters listed below with a scan tool:
|
|
| • |
The MIL Control Circuit Low Voltage Test Status
|
| • |
The MIL Control Circuit Open Test Status
|
| • |
The MIL Control Circuit High Voltage Test Status
Each parameter should display OK or Not Run. |
| 3. |
Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
|
|
| Circuit/System Testing |
| 1. |
Ignition OFF, disconnect the X1 harness connector at the K20 ECM.
|
|
| 2. |
Ignition ON, the MIL should not illuminate.
|
|
| 3. |
If the MIL is illuminated, test the MIL control circuit terminal 46 X1 for a short to ground. If the circuit tests normal, replace the P 16 instrument panel cluster.
|
|
| 4. |
Connect a 3 A fused jumper wire between the MIL control circuit terminal 46 X1 and ground. The MIL should turn on.
|
|
| 5. |
If the MIL illuminates, replace the ECM.
|
|
| 6. |
If the MIL does not illuminate, test the MIL control circuit for a short to voltage or an open/high resistance. If the MIL control circuit tests OK, test the instrument panel cluster ignition circuit for a short to ground or open/high resistance. If the circuits test normal, replace the instrument panel cluster/bulb.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Instrument Cluster Replacement
|
|
| • |
Control Module References
for replacement, setup, and programming.
|
|
