PRE-RELEASE
DTC U2099
| DTC U2099 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptor |
DTC U2099 00
High Speed Communication Enable Circuit
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|
Serial Data Communication Enable
|
U2099, U0100-U0299¹
|
U0100-U0299
|
U0100-U0299
2
|
-
|
|
¹ Vehicle will not start.
2 History only. If cleared the DTC will return after several ignition cycles. |
||||
| Circuit/System Description |
The body control module (BCM) activates the serial data communication enable circuit, when the ignition key is in ACC, ON or START. The serial data communication enable circuit wakes up the modules for serial data buss communication.
| Conditions for Running the DTC |
| • |
System voltage is between 9-16 V.
|
|
| • |
The vehicle power mode master requires serial data communication to occur.
|
|
| Conditions for Setting the DTC |
The BCM senses a short to ground on the serial data communication enable circuit.
| Action Taken When the DTC Sets |
| • |
The output command is turned off while the malfunction is present.
|
|
| • |
The modules use a default value for the missing parameters until the next ignition cycle.
|
|
| • |
The module(s) is never signaled, therefore the specific subsystem(s) will not function.
|
|
| • |
The vehicle will not start while the circuit is shorted to ground.
|
|
| Conditions for Clearing the DTC |
| • |
A current DTC clears when the malfunction is no longer present.
|
|
| • |
A history DTC clears when the module ignition cycle counter reaches the reset threshold of 50, without a repeat of the malfunction.
|
|
| Diagnostic Aids |
| • |
Use the DMM MIN/MAX function to capture/locate intermittent conditions.
|
|
| • |
Short to ground will also set multiple history no communication codes for GMLAN high speed modules.
|
|
| Reference Information |
Schematic Reference
Data Communication Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Data Link Communications Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
| Circuit/System Testing |
| Note | ||
|
Use the schematic to determine which control modules are on the BCM communications enable circuit 23, X4. |
| 1. |
Ignition OFF, disconnect the harness connector at the most easily accessible control module on the BCM communications enable circuit.
|
|
| 2. |
Ignition ON, repeat the test for the current DTCs. DTC U2099 should still be stored.
|
|
| 3. |
If the DTC becomes history, replace the control module.
|
|
| 4. |
With the prior control modules disconnected, repeat steps 1 and 2 for each control module on the circuit except the BCM.
|
|
| 5. |
Ignition OFF, disconnect the X 4 harness connector at the K9 BCM.
|
|
| 6. |
Test for infinite resistance between the serial data communication enable circuit terminal 23 and ground.
|
|
| 7. |
If less than infinite resistance, repair the enable circuit for a short to ground.
|
|
| 8. |
If all circuits tests normal, replace the K9 BCM.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for module replacement, setup, and programming
