PRE-RELEASE
DTC B2645
| DTC B2645 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
has overviews of all diagnostic categories.
|
|
| DTC Descriptors |
DTC B2645 03
Ambient Light Sensor Circuit Low Voltage
DTC B2645 07
Ambient Light Sensor Circuit High Voltage
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|
Ambient Light Sensor Control
|
B2645 03
|
B2645 03
|
B2645 07
|
-
|
|
Ground
|
-
|
1
|
-
|
-
|
|
1. Daytime Running Light Malfunction
|
||||
| Circuit/System Description |
The ambient light sensor is used to monitor outside lighting conditions. The ambient light sensor provides a voltage signal that will vary between 1.4-4.5 V depending on outside lighting conditions. The body control module (BCM) monitors the ambient light sensor signal circuit to determine if outside lighting conditions are correct for either daytime running lights or automatic lamp control when the headlamp switch is in the AUTO position. In daylight conditions the BCM will command the daytime running lights ON. During low light conditions the BCM will command the low beam headlamps ON.
| Conditions for Running the DTC |
Ignition ON.
| Conditions for Setting the DTC |
B2645 03
The BCM detects a voltage below threshold on the signal circuit.B2645 07
The BCM detects a voltage above threshold on the signal circuit.| Action Taken When the DTC Sets |
The condition for setting the DTC is not longer present.
| Conditions for Clearing the DTC |
The condition for setting the DTC is not longer present.
| Reference Information |
Schematic Reference
Exterior Lights Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References for information on diagnostic tools
| Circuit/System Verification |
Ignition ON, observe the scan tool Ambient Light Sensor parameter. The reading should be between 1.4-4.5 V and change with ambient light changes.
| Circuit/System Testing |
| 1. |
Ignition OFF, disconnect the harness connector at the B10B Ambient Light/Sunload Sensor.
|
|
| 2. |
Test for less than 5 Ω between the ground circuit harness connector terminal 6 and ground.
|
|
| 3. |
If greater than the specified range, test the low reference circuit for an open/high resistance.
|
|
| 4. |
Ignition ON, test for 4.8-5.2 V between the signal circuit harness connector terminal 5 and ground.
|
|
| 5. |
If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K9 Body Control Module.
|
|
| 6. |
If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.
|
|
| 7. |
If all circuits test normal, test or replace the B10B Ambient Light/Sunload Sensor.
|
|
| Component Testing |
Dynamic Test
| 1. |
Ignition ON, observe the scan tool Ambient Light Sensor parameter. The reading should be between 1.4-4.5 V and change with ambient light changes.
|
|
| 2. |
Test the B10B Ambient Light/Sunload Sensor by varying the ambient light while monitoring the sensors voltage output.
|
|
| 3. |
Verify that the voltage output is within the range of the specification.
|
|
| 4. |
If not within the specified range, replace the B10B Ambient Light/Sunload Sensor.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Sun Load Temperature and Headlamp Automatic Control Ambient Light Sensor Replacement
|
|
| • |
Control Module References
for information on BCM replacement, setup, and programming
|
|
