PRE-RELEASE
DTC B3881 or B3882
| DTC B3881 or B3882 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
has overviews of all diagnostic categories.
|
|
| DTC Descriptors |
DTC B3881 02
Tail Lamp Circuit Short to Ground
DTC B3882 02
Right Tail Lamp Circuit Short to Ground
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|
Tail Lamp Control
|
B3881 02
|
1
|
2
|
-
|
|
Right Tail Lamp Control
|
B3882 02
|
1
|
2
|
-
|
|
1. Tail lamp always OFF.
2. Tail lamp always ON. |
||||
| Circuit/System Description |
The headlamp switch is supplied with ground at all times. When the headlamp switch is placed in either the park or low beam position, ground is applied to the Tail lamp signal circuit to the body control module (BCM). The BCM responds by applying battery voltage to the left and to the right tail lamp control circuits. This energizes the tail lamps, side marker lamps, position lamps, park/turn signal lamps.
| Conditions for Running the DTC |
The headlamp switch is in park or low beam position.
| Conditions for Setting the DTC |
B3881 02 or B3882 02
The BCM detects a short to ground on the control circuit.| Action Taken When the DTC Sets |
The appropriate tail lamp is inoperative.
| Conditions for Clearing the DTC |
The condition for setting the DTC is no longer present.
| Reference Information |
Schematic Reference
Exterior Lights Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References for information on diagnostic tools
| Circuit/System Verification |
Ignition ON, perform the appropriate Rear Park Lamp test. The appropriate tail lamp should be ON/OFF.
| Circuit/System Testing |
| 1. |
Ignition OFF, disconnect the appropriate harness connector at the tail lamp listed below:
|
|
| • |
E42L Tail Lamp Assembly - Auxiliary Left
|
| • |
E42R Tail Lamp Assembly - Auxiliary Right
|
| 2. |
Test for less than 5 Ω between the appropriate ground circuit harness connector terminal listed below and ground:
|
|
| • |
E42L Tail Lamp Assembly - Auxiliary Left harness connector terminal F
|
| • |
E42R Tail Lamp Assembly - Auxiliary Right harness connector terminal F
|
| • |
If greater than the specified value, test the appropriate ground circuit for an open circuit/high resistance.
|
| 3. |
Connect a test lamp between the appropriate control circuit harness connector terminal listed below and ground:
|
|
| • |
E42L Tail Lamp Assembly - Auxiliary Left harness connector terminal A
|
| • |
E42R Tail Lamp Assembly - Auxiliary Right harness connector terminal A
|
| 4. |
Command the appropriate Rear Park Lamp test with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
|
|
| 5. |
If the test lamp is always ON, test the appropriate control circuit for a short to voltage. If the circuit tests normal, replace the K9 Body Control Module.
|
|
| 6. |
If the test lamp is always OFF, test the appropriate control circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 Body Control Module.
|
|
| 7. |
If all circuits test normal, test or replace the appropriate tail lamp.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Tail Lamp Replacement
|
|
| • |
Control Module References
for information on BCM replacement, setup, and programming
|
|
