PRE-RELEASE
DTC B3887 or B3888
| DTC B3887 or B3888 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
has overviews of all diagnostic categories.
|
|
| DTC Descriptors |
DTC B3887 02
Trailer Left Turn Signal Circuit Short to Ground
DTC B3887 04
Trailer Left Turn Signal Circuit Open
DTC B3888 02
Trailer Right Turn Signal Circuit Short to Ground
DTC B3888 04
Trailer Right Turn Signal Circuit Open
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|
Trailer Left Turn Signal
|
3887 02
|
3887 04
|
-
|
-
|
|
Trailer Right Turn Signal
|
B3888 02
|
B3888 04
|
-
|
-
|
| Circuit/System Description |
Ground is applied at all times to the turn signal/multifunction switch. When the turn signal/multifunction switch is placed in either the turn right or turn left position, ground is applied to the body control module (BCM) through either the right turn or left turn signal switch signal circuit. The BCM sends this message to the trailer lighting converter. The trailer lighting converter then applies a voltage to the appropriate trailer turn signal lamps through there respective voltage supply circuits.
| Conditions for Running the DTC |
B3887 02, B3887 04, B3888 02 and B3888 04
The appropriate trailer turn signal is active.| Conditions for Setting the DTC |
B3887 02 or B3888 02
The trailer lighting converter detects a short to ground on the control circuit.B3887 04 or B3888 04
The trailer lighting converter detects an open control circuit.| Action Taken When the DTC Sets |
The appropriate trailer turn signal lamp is inoperative.
| Conditions for Clearing the DTC |
The condition for setting the DTC is not longer present.
| Reference Information |
Schematic Reference
Trailer Connector/Provision Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Exterior Lighting Systems Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References for information on diagnostic tools
| Circuit/System Verification |
Ignition ON, perform the appropriate Trailer Turn Signal Lamp test. The appropriate trailer turn signal lamp should be ON/OFF.
| Circuit/System Testing |
| 1. |
Ignition OFF, test for less than 5 Ω between the X88 Trailer Connector terminal 3, 11, 13 and ground.
|
|
| 2. |
If greater than the specified value, test the appropriate ground circuit for an open circuit/high resistance.
|
|
| 3. |
Connect a test lamp between the appropriate X88 Trailer Connector terminal listed below and ground.
|
|
| • |
X88 Trailer Connector terminal 1
|
| • |
X88 Trailer Connector terminal 4
|
| 4. |
Command the appropriate Trailer Turn Signal Lamp Active/Inactive test with a scan tool. The test lamp should turn ON and OFF when changing between the commanded states.
|
|
| 5. |
If the test lamp is always ON, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K68 Trailer Lighting Control Module.
|
|
| 6. |
If the test lamp is always OFF, test the signal circuit for a short to ground or an open/high resistance. If the circuits test normal, replace the K68 Trailer Lighting Control Module.
|
|
| 7. |
If all the circuits test normal, test the appropriate turn signal lamp circuit at the trailer.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for trailer lighting converter replacement, setup and programming
