DTC C0575, C0580, C0585, or C0590
|
|
DTC C0575, C0580, C0585, or C0590
|
DTC C0575 02
Left Front Damper Actuator Circuit Short to Ground
DTC C0575 04
Left Front Damper Actuator Circuit Open
DTC C0575 0F
Left Front Damper Actuator Circuit Signal Erratic
DTC C0580 02
Right Front Damper Actuator Circuit Short to Ground
DTC C0580 04
Right Front Damper Actuator Circuit Open
DTC C0580 0F
Right Front Damper Actuator Circuit Signal Erratic
DTC C0585 02
Left Rear Damper Actuator Circuit Short to Ground
DTC C0585 04
Left Rear Damper Actuator Circuit Open
DTC C0585 0F
Left Rear Damper Actuator Circuit Signal Erratic
DTC C0590 02
Right Rear Damper Actuator Circuit Short to Ground
DTC C0590 04
Right Rear Damper Actuator Circuit Open
DTC C0590 0F
Right Rear Damper Actuator Circuit Signal Erratic
|
Diagnostic Fault Information
|
|
Circuit
|
Short to Ground
|
Open/High Resistance
|
Short to Voltage
|
Signal Performance
|
Left Front Damper Actuator Control High
|
C0575 02
|
C0575 04
|
C0575 02
|
C0575 0F
|
Right Front Damper Actuator Control High
|
C0580 02
|
C0580 04
|
C0580 02
|
C0580 0F
|
Left Rear Damper Actuator Control High
|
C0585 02
|
C0585 04
|
C0585 02
|
C0585 0F
|
Right Rear Damper Actuator Control High
|
C0590 02
|
C0590 04
|
C0590 02
|
C0590 0F
|
Left Front Damper Actuator Control Low
|
C0575 02
|
C0575 04
|
C0575 04
|
C0575 0F
|
Right Front Damper Actuator Control Low
|
C0580 02
|
C0580 04
|
C0580 04
|
C0580 0F
|
Left Rear Damper Actuator Control Low
|
C0585 02
|
C0585 04
|
C0585 04
|
C0585 0F
|
Right Rear Damper Actuator Control Low
|
C0590 02
|
C0590 04
|
C0590 04
|
C0590 0F
|
|
Circuit/System Description
|
The suspension control module commands variable levels of current to each shock absorber actuator in response to rough road, braking or abrupt steering maneuver driving conditions. The current variation is performed by pulse width modulation (PWM) of the system voltage. The suspension control module continuously measures the actual current of each actuator. When a deviation between commanded and actual current is detected, a DTC is set.
|
Conditions for Running the DTC
|
System voltage is between 9-16 V.
|
Conditions for Setting the DTC
|
C0575 02, C0580 02, C0585 02, and C0590 02
|
•
|
A short to voltage or short to ground on the control high circuit is detected.
|
|
•
|
A short to ground on the control low circuit is detected.
|
C0575 04, C0580 04, C0585 04, and C0590 04
|
•
|
An open circuit on the control high or control low circuit is detected.
|
|
•
|
A short to voltage on the control low circuit is detected.
|
C0575 0F, C0580 0F, C0585 0F, and C0590 0F
An erratic current on the actuator circuit is detected.
|
Action Taken When the DTC Sets
|
|
•
|
The electronic suspension control is disabled for the duration of the ignition cycle.
|
|
•
|
The driver information center displays the SERVICE SUSPENSION SYSTEM message.
|
|
Conditions for Clearing the DTC
|
|
•
|
A present DTC will clear on the next consecutive malfunction-free ignition cycle.
|
|
•
|
A history DTC will clear after 41 consecutive malfunction-free ignition cycles.
|
Schematic Reference
Electronic Suspension Control Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Electronic Suspension Control Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References
for scan tool information
|
Circuit/System Verification
|
Ignition ON, command the Damper Actuator Increase and Decrease with a scan tool while observing the Damper Actuator Command parameter. The reading should vary between 0-1 600 mA. Listen/feel the damper actuator. The component should activate when changing between the commanded states.
|
1.
|
Ignition OFF, disconnect the harness connector at the K19 Suspension Control Module and at the appropriate damper actuator.
|
|
2.
|
Ignition ON, test for less than 0.3 V between the circuit terminal listed below and ground:
|
|
|
•
|
Front left damper actuator control circuit terminal 14 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Front right damper actuator control circuit terminal 15 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear left damper actuator control circuit terminal 4 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear right damper actuator control circuit terminal 3 at the K19 Suspension Control Module harness connector
|
|
3.
|
If greater than the specified value, test the control circuit for a short to voltage.
|
|
4.
|
Test for less than 0.3 V between the circuit terminal listed below and ground:
|
|
|
•
|
Front left damper actuator control circuit terminal 13 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Front right damper actuator control circuit terminal 16 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear left damper actuator control circuit terminal 5 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear right damper actuator control circuit terminal 2 at the K19 Suspension Control Module harness connector
|
|
5.
|
If greater than the specified value, test the control circuit for a short to voltage.
|
|
6.
|
Ignition OFF, test for infinite resistance between the circuit terminal listed below and ground:
|
|
|
•
|
Front left damper actuator control circuit terminal 14 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Front right damper actuator control circuit terminal 15 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear left damper actuator control circuit terminal 4 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear right damper actuator control circuit terminal 3 at the K19 Suspension Control Module harness connector
|
|
7.
|
If less than the specified value, test the control circuit for a short to ground.
|
|
8.
|
Test for infinite resistance between the circuit terminal listed below and ground:
|
|
|
•
|
Front left damper actuator control circuit terminal 13 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Front right damper actuator control circuit terminal 16 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear left damper actuator control circuit terminal 5 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear right damper actuator control circuit terminal 2 at the K19 Suspension Control Module harness connector
|
|
9.
|
If less than the specified value, test the control circuit for a short to ground.
|
|
10.
|
Test for infinite resistance between the circuit terminals listed below:
|
|
|
•
|
Front left damper actuator control circuit terminals 14 and 13 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Front right damper actuator control circuit terminals 15 and 16 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear left damper actuator control circuit terminals 4 and 5 at the K19 Suspension Control Module harness connector
|
|
|
•
|
Rear right damper actuator control circuit terminals 3 and 2 at the K19 Suspension Control Module harness connector
|
|
11.
|
If less than the specified value, test the control circuits for a short circuit.
|
|
12.
|
Test for less than 5 Ω between the circuit terminals listed below:
|
|
|
•
|
Front left damper actuator control circuit terminal 13 at the K19 Suspension Control Module harness connector and terminal 5 at the Q37LF Shock Absorber Actuator - Left Front harness connector
|
|
|
•
|
Front right damper actuator control circuit terminal 16 at the K19 Suspension Control Module harness connector and terminal 5 at the Q37RF Shock Absorber Actuator - Right Front harness connector
|
|
|
•
|
Rear left damper actuator control circuit terminal 5 at the K19 Suspension Control Module harness connector and terminal B at the Q37LR Shock Absorber Actuator - Left Rear harness connector
|
|
|
•
|
Rear right damper actuator control circuit terminal 2 at the K19 Suspension Control Module harness connector and terminal B at the Q37RR Shock Absorber Actuator - Right Rear harness connector
|
|
13.
|
If greater than the specified value, test the control circuit for an open/high resistance.
|
|
14.
|
Test for less than 5 Ω between the circuit terminals listed below:
|
|
|
•
|
Front left damper actuator control circuit terminal 14 at the K19 Suspension Control Module harness connector and terminal 6 at the Q37LF Shock Absorber Actuator - Left Front harness connector
|
|
|
•
|
Front right damper actuator control circuit terminal 15 at the K19 Suspension Control Module harness connector and terminal 6 at the Q37RF Shock Absorber Actuator - Right Front harness connector
|
|
|
•
|
Rear left damper actuator control circuit terminal 4 at the K19 Suspension Control Module harness connector and terminal A at the Q37LR Shock Absorber Actuator - Left Rear harness connector
|
|
|
•
|
Rear right damper actuator control circuit terminal 3 at the K19 Suspension Control Module harness connector and terminal A at the Q37RR Shock Absorber Actuator - Right Rear harness connector
|
|
15.
|
If greater than the specified value, test the control circuit for an open/high resistance.
|
|
16.
|
If all circuits test normal, test or replace the damper actuator and verify the DTC does not reset.
|
|
17.
|
If the DTC resets, replace the K19 Suspension Control Module.
|
Static Test
|
1.
|
Ignition OFF, disconnect the harness connector at the appropriate damper actuator.
|
|
2.
|
Test for 2-3 Ω between the control terminal A and the low reference terminal B.
|
|
3.
|
If not within the specified range, replace the damper actuator.
|
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.
