PRE-RELEASE
DTC C0750, C0755, C0760, or C0765
| DTC C0750, C0755, C0760, or C0765 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptor |
DTC C0750 03
Left Front Tire Pressure Sensor Low Voltage
DTC C0750 29
Left Front Tire Pressure Sensor Too Few Pulses
DTC C0750 39
Left Front Tire Pressure Sensor Internal Malfunction
DTC C0755 03
Right Front Tire Pressure Sensor Low Voltage
DTC C0755 29
Right Front Tire Pressure Sensor Too Few Pulses
DTC C0755 39
Right Front Tire Pressure Sensor Internal Malfunction
DTC C0760 03
Left Rear Tire Pressure Sensor Low Voltage
DTC C0760 29
Left Rear Tire Pressure Sensor Too Few Pulses
DTC C0760 39
Left Rear Tire Pressure Sensor Internal Malfunction
DTC C0765 03
Right Rear Tire Pressure Sensor Low Voltage
DTC C0765 29
Right Rear Tire Pressure Sensor Too Few Pulses
DTC C0765 39
Right Rear Tire Pressure Sensor Internal Malfunction
| Circuit/System Description |
The tire pressure monitor system has a radio frequency transmitting pressure sensor in each wheel/tire assembly. As vehicle speed increases, centrifugal force closes the sensors internal roll switch, which puts the sensor into rolling mode. The remote control door lock receiver receives and sends the data to the body control module (BCM). The BCM translates the data contained in the tire pressure sensor radio frequency transmissions into sensor presence, sensor mode, and tire pressure. Once vehicle speed is greater than 40 km/h (25 MPH), the remote function receiver module waits for the sensors to go into rolling mode. If one or more sensors do not go into rolling mode, or do not transmit at all, the BCM will set DTC C0750, C0755, C0760, or C0765 respectively.
| Conditions for Running the DTC |
The vehicle speed is greater than 40 km/h (25 mph).
| Conditions for Setting the DTC |
| • |
A sensor does not transmit or transmits invalid data.
|
|
| • |
A sensor low battery condition.
|
|
| Action Taken When the DTC Sets |
| • |
The tire pressure monitor system indicator icon on the instrument cluster flashes for 1 min. and then remains illuminated after the ignition switch is cycled ON and the instrument cluster bulb check is complete.
|
|
| • |
If equipped, the driver information center will also display a service tire monitor type message.
|
|
| Conditions for Clearing the DTC |
A current DTC will clear when the malfunction is no longer present and 1 ignition cycle occurs.
| Diagnostic Aids |
| • |
Aftermarket wheel valve system locations can cause a sensor to not function correctly.
|
|
| • |
A sensor may have been damaged due to a previous wheel/tire service or flat tire event.
|
|
| • |
Occasionally sensor transmissions are not received by the remote function receiver module due to vehicle level radio frequency interference from items such as but not limited to aftermarket ignition systems, DVD players, CB radios, or metallic type window tinting.
|
|
| Reference Information |
Schematic Reference
Tire Pressure Monitoring System Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Tire Pressure Monitor Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Verification |
Drive over 20 km/h (12 MPH) for 9 min. Observe the scan tool tire pressures sensor pressure parameters. Verify the simulated tire pressures do not differ more than +/-30 kPa (3.6 PSI) of the scan tool reading.
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Tire Pressure Indicator Sensor Replacement
|
|
| • |
Tire Pressure Indicator Sensor Learn
|
|
