PRE-RELEASE
Body Dimensions
| Body Dimensions |
| Point to Point Measurements |
Point-to-point measurements are for reference only. All measurements are given in millimeters. Use these measurements for diagnosing and estimating. Point-to-point measurements are duplicated with tram bar pointers set at equal lengths. All the marks, holes, slots, and fasteners are measured to the center. All dimensions are symmetrical unless otherwise specified.
Following dimensions are suitable for determining whether the vehicle should be mounted on a frame machine. Complete dimensional data are available from the relevant frame-machine manufacturer.
Figure B shows incorrect measuring direction for readings
| Pos | Dimensions in mm | Measure Points |
|
1
|
4763
|
Total Length Front Bumper Member - Rear Bumper Abutment
|
|
2
|
1552
|
Hole in outer bracket for headlamp frame (*) - Hole in outer bracket for headlamp frame (*) threaded hole for headlamp
|
|
3
|
1435
|
Hole in outer bracket for headlamp frame (*) - Inner weld-bolt
|
|
4
|
365
|
Hole in outer bracket for headlamp frame (*) - Inner weld-bolt
|
|
5
|
1240
|
Inner weld-bolt - Inner weld-bolt
|
|
6
|
1617
|
Hole in outer bracket for headlamp frame (*) - Lower hood hinge bracket, centre of bolt head
|
|
7
|
1552
|
Lower hood hing bracket, centre of bolt head centre of bolt head
|
|
8
|
1537
|
Spacing between flanges for sealing-strips upper edge on sill
|
|
9
|
1539
|
Spacing between flanges for sealing-strips upper edge on sill (inner panel)
|
|
10
|
1481
|
Lower part of A-pillar in corner to windscreen cross-member - Upper part of A-pillar, interior radius, where the dimension is largest diagonally. Radius to radius A-pillar.
|
(*) = hole centre is starting position for dimensioning.
| Body rear readings |
| Pos | Dimensions in mm | Measure Points |
|
11
|
1134
|
Distance between the corners to tail-lamp
|
|
12
|
655
|
Corner to tail-lamp - Pop-rivet hole
|
| Body side readings |
| Pos | Dimensions in mm | Measure Points |
|
18
|
1088
|
Front hinge; rear, upper hole (*) - Rear hinge, front lower hole (*)
|
|
19
|
1132
|
Front hinge; rear, lower hole (*) - Rear hinge, front upper hole (*)
|
|
20
|
860
|
Rear hinge; front, upper hole (*) - Strike plate upper hole (*)
|
|
21
|
942
|
Rear hinge; front, lower hole (*) - Strike plate upper hole (*)
|
(*) = hole centre is starting position for dimensioning.
| Body B-pillar readings |
| Pos | Dimensions in mm | Measure Points |
|
22
|
1599
|
Bolt hole for belt attachment (*). Diagonal dimension to hole for upper belt attachment
|
|
23
|
1474
|
Distance between rear clip hole upper edge (*)
|
(*) = hole centre is starting position for dimensioning.
| Under-body readings |
| Pos | Dimensions in mm | Measure Points |
|
24
|
1445
|
Front subframe mounting, centre of bolt head LH side - Hole in floor reinforcement RH side (*)
|
|
25
|
1443
|
Front subframe mounting, centre of bolt head RH side - Hole in floor reinforcement LH side (*)
|
|
26
|
1494
|
Distance between inside of sill edge
|
|
27
|
1494
|
Distance between inside of sill edge
|
|
28
|
2089
|
Hole in member LH side (*) - Hole in member RH side (*)
|
|
29
|
2089
|
Hole in member RH side (*) - Hole in member LH side (*)
|
