PRE-RELEASE
DTC B3618
| DTC B3618 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
has overviews of all diagnostic categories.
|
|
| DTC Descriptor |
DTC B3618 00
Exterior Liftgate Unlatch Switch Circuit Malfunction
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|
Rear Compartment Lid Exterior Release Switch Signal
|
B3618 00
|
1
|
1
|
-
|
|
Rear Compartment Lid Exterior Release Switch Ground
|
-
|
1
|
-
|
-
|
|
1. Trunk Release Malfunction
|
||||
| Circuit/System Description |
The exterior rear compartment lid release switch receives a signal from the body control module (BCM). When the exterior rear compartment lid release switch is activated the signal circuit is pulled to ground. The BCM applies battery positive voltage to the trunk release relay control circuit which energizes the relay. The trunk release relay is grounded at all times. With the relay coil energized, the relay switch contacts close allowing battery voltage to flow to the rear compartment lid release actuator causing the rear compartment lid to release.
| Conditions for Running the DTC |
Battery voltage must be between 9-16 V.
| Conditions for Setting the DTC |
The BCM detects a fault in the exterior trunk release switch signal circuit.
| Action Taken When the DTC Sets |
The rear compartment latch will not operate.
| Conditions for Clearing the DTC |
| • |
This DTC will be current for as long as the fault is present.
|
|
| • |
When the fault is no longer present, the DTC will be a history DTC.
|
|
| • |
A history DTC will clear after 50 ignition cycles.
|
|
| Reference Information |
Schematic Reference
Release Systems Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Luggage Compartment Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References
| Circuit/System Verification |
Command the trunk release by using the exterior rear compartment lid release switch. The rear compartment lid release actuator should release the trunk lid.
| Circuit/System Testing |
| 1. |
Ignition OFF, disconnect the harness connector at the S58A Rear Compartment Lid Unlatch Switch - Exterior.
|
|
| 2. |
Test for less than 5 Ω between the ground circuit terminal 3 and ground.
|
|
| 3. |
If greater than the specified range, test the ground circuit for an open/high resistance.
|
|
| 4. |
Disconnect the X6 harness connector at the K9 Body Control Module.
|
|
| 5. |
Ignition ON, test for less than 0.3 V between the signal circuit terminal 1 at the S58A Rear Compartment Lid Unlatch Switch - Exterior harness connector and ground.
|
|
| 6. |
If greater than the specified value, test the signal circuit for a short to voltage.
|
|
| 7. |
Ignition OFF, test for infinite resistance between the signal circuit terminal 1 at the S58A Rear Compartment Lid Unlatch Switch - Exterior harness connector and ground.
|
|
| 8. |
If less than the specified value, test the signal circuit for a short to ground.
|
|
| 9. |
Test for less than 5 Ω between the signal circuit terminal 1 at the S58A Rear Compartment Lid Unlatch Switch - Exterior harness connector and terminal 15 X6 at the K9 Body Control Module harness connector.
|
|
| 10. |
If greater then the specified value, test the signal circuit for an open circuit/high resistance.
|
|
| 11. |
If all circuits test normal, test or replace the S58A Rear Compartment Lid Unlatch Switch - Exterior.
|
|
| Component Testing |
Static Test
| 1. |
Ignition OFF, disconnect the harness connector at the S58A Rear Compartment Lid Unlatch Switch - Exterior
|
|
| 2. |
Test for infinite resistance between the signal terminal 1 and the ground terminal 3 with the switch in the open position
|
|
| 3. |
If not within the specified range, replace the S58A Rear Compartment Lid Unlatch Switch - Exterior.
|
|
| 4. |
Test for less than 5 Ω between the signal terminal 1 and the ground terminal 3 with the switch in the closed position.
|
|
| 5. |
If less than the specified value, replace the S58A Rear Compartment Lid Unlatch Switch - Exterior.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Rear Compartment Lid Release Switch Replacement
|
|
| • |
Control Module References
|
|
