PRE-RELEASE
DTC P15A1
| DTC P15A1 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provide an overview of each diagnostic category.
|
|
| DTC Descriptor |
DTC P15A1
Fuel Economy Mode Switch Performance
| Diagnostic Fault Information |
| Circuit | Short to Ground | High Resistance | Open | Short to Voltage | Signal Performance |
| Fuel Economy Mode Switch 5 V Reference | P159F | P159F, P15A1 | P159F | P15A0 | P15A1 |
| Fuel Economy Mode Switch Signal | P159F | P159F | P159F | P15A0 | P15A1 |
| Fuel Economy Mode Switch Ground | - | P15A0, P15A1 | P15A0 | - | P15A1 |
| Circuit Description |
The ECM supplies 5 V reference voltage, through the 5 V reference voltage circuit, to the S87 fuel economy mode switch. This reference voltage causes current to flow through a series of resistors in the switch to the ground circuit's switch. The ECM monitors the 5 V reference voltage through a discrete fuel economy mode switch signal circuit. When the switch button is momentarily pressed, the switch contacts allow the 5 V reference voltage signal to by-pass one of the resistors. The ECM detects the resulting voltage drop as a fuel economy mode request and sends a GMLAN message to the transmission control module (TCM) confirming the request. When the TCM receives the request, throttle progressions and transmission shift points are modified to optimize fuel efficiency. The instrument panel cluster (IPC) also receives the fuel economy mode request message from the ECM and illuminates the fuel economy mode indicator lamp. The fuel economy mode switch button must be pressed for between 0.094-1.5 s to activate the fuel economy mode.
| Conditions for Running the DTC |
| • |
The ignition key is turned to ON.
|
|
| • |
DTC P15A1 runs continuously when the above condition is met.
|
|
| Conditions for Setting the DTC |
The ECM detects that the voltage on the fuel economy mode switch signal wire is in an indeterminate range.
| Action Taken When the DTC Sets |
DTC P15A1 is a Type B DTC.
| Conditions for Clearing the MIL/DTC |
DTC P15A1 is a Type B DTC.
| Reference Information |
Schematic Reference
Engine Controls Schematics (3.0L (LF1)) Engine Controls Schematics (2.8L (LAU))
Connector End View Reference
Component Connector End Views
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Verification |
| 1. |
Verify that DTCs P159F and P15A0 are not set.
|
|
| 2. |
If either or both of the DTCs are set, diagnose those DTCs first.
|
|
| 3. |
Ignition ON, verify the fuel economy mode indicator lamp on the instrument panel cluster is not illuminated.
|
|
| 4. |
Ignition ON, verify the fuel economy mode indicator lamp on the instrument panel cluster illuminates when the fuel economy mode switch button is pressed.
|
|
| 5. |
Engine on, check the DTC information with a scan tool. DTC P15A1 should not be set.
|
|
| 6. |
Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data.
|
|
| Circuit/System Testing |
| Note | ||
|
You must perform the Circuit/System Verification before proceeding with Circuit/System Testing. |
| 1. |
Ignition OFF, disconnect the harness connector at the S87 Fuel Economy Mode switch.
|
|
| 2. |
Ignition OFF, and all vehicle systems OFF, test for less than 5 Ω between ground circuit terminal 2 of the harness connector and ground. |
|||||||
| 3. |
If greater than the specified value, test the ground circuit for an open/high resistance and repair as necessary.
|
|
| 4. |
Test for 266-294 Ω between 5 V reference voltage circuit terminal 9 and signal circuit terminal 10 of the S87 fuel economy mode switch.
|
|
| 5. |
If not the specified range, replace the S87 fuel economy mode switch.
|
|
| 6. |
Test for 1,414-1,562 Ω between 5 V reference voltage circuit terminal 9 and ground circuit terminal 2 of the S87 fuel economy mode switch.
|
|
| 7. |
If not the specified range, replace the S87 fuel economy mode switch.
|
|
| 8. |
With the fuel economy mode switch button depressed, test for 486-538 Ω between 5 V reference voltage circuit terminal 9 and ground circuit terminal 2 of the S87 fuel economy mode switch.
|
|
| 9. |
If not the specified range, replace the S87 fuel economy mode switch.
|
|
| 10. |
Disconnect the X2 harness connector at the ECM.
|
|
| 11. |
Test for less than 5 Ω between 5 V reference voltage circuit terminal 14 of the ECM harness connector and 5 V reference voltage circuit terminal 9 of the fuel economy mode switch harness connector.
|
|
| 12. |
If greater than the specified value, repair the 5 V reference voltage circuit as necessary.
|
|
| 13. |
Test for less than 5 Ω between signal circuit terminal 29 of the ECM harness connector and signal circuit terminal 10 of the fuel economy mode switch harness connector.
|
|
| 14. |
If greater than the specified value, repair the signal circuit as necessary.
|
|
| 15. |
If all circuits test normal, replace the K20 ECM.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for ECM replacement, setup and programming
