PRE-RELEASE
DTC P2096
| DTC P2096 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptor |
DTC P2096
Post Catalyst Fuel Trim System Low Limit
| Circuit Description |
Fuel trim is used by the engine control module (ECM) to keep the post catalyst HO2S voltage within a range of 580-665 mV. This allows optimal catalyst efficiency under light load conditions, such as at idle or a steady cruise. The ECM constantly monitors how lean or rich the fuel trim is commanded, to determine if the fuel trim is greater than the calibrated amount.
| Conditions for Running the DTC |
| • |
Before the ECM can report DTC P2096, DTCs P0030, P0031, P0032, P0130, P0131, P0132, P0133, P0135, P0137, P0138, P0140, P0141, P2232, P2235, P2270, P2271, P2272, and P2273 must run and pass.
|
|
| • |
DTC P0100, P0101, P0102, P0103, P0111, P0112, P0113, P0116, P0117, P0118, P0119, P0420, P0443, P0458, or P0459 is not set.
|
|
| • |
The engine speed is 1,080-3,480 RPM.
|
|
| • |
The engine load is 17-20 % and steady.
|
|
| • |
The Closed Loop fuel control is active for greater than 1 s.
|
|
| • |
The front and rear HO2S are in Closed Loop.
|
|
| • |
The calculated exhaust gas temperature is greater than 250°C (482°F).
|
|
| • |
DTC P2096 runs continuously when the conditions above have been met for greater than 200 s.
|
|
| Conditions for Setting the DTC |
The lean correction limit for a condition causing a rich air/fuel mixture has been exceeded for a predetermined amount of time. The condition exists for greater than 4 s or for a cumulative of 30 s.
| Action Taken when the DTC Sets |
DTC P2096 is a Type B DTC.
| Conditions for Clearing the MIL/DTC |
DTC P2096 is a Type B DTC.
| Diagnostic Aids |
An HO2S will not cause this DTC to set without the occurrence of circuit related HO2S DTCs. Do not replace an HO2S to address this DTC.
| Reference Information |
Schematic Reference
Engine Controls Schematics (3.0L (LF1)) Engine Controls Schematics (2.8L (LAU))
Connector End View Reference
Component Connector End Views
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Verification |
| 1. |
Ignition ON, observe the scan tool DTC information. Verify there is no other HO2S or fuel trim DTC set.
|
|
| 2. |
If any other HO2S or fuel trim DTC is set, refer to
Diagnostic Trouble Code (DTC) List - Vehicle
.
|
|
| 3. |
Verify none of the following conditions exist:
|
|
| • |
Rich fuel injectors-Refer to
Fuel Injector Solenoid Coil Test (LAU)
Fuel Injector Solenoid Coil Test (LF1, LFW)
.
|
| • |
High fuel system pressure-Refer to
Fuel System Diagnosis (LF1 China)
Fuel System Diagnosis (LF1 Except China)
Fuel System Diagnosis (LAU China)
Fuel System Diagnosis (LAU Except China)
.
|
| • |
Fuel that is contaminated-Refer to
Alcohol/Contaminants-in-Fuel Diagnosis (Special Tool)
Alcohol/Contaminants-in-Fuel Diagnosis (Without Special Tool)
.
|
| • |
Fuel saturation of the evaporative emissions (EVAP) canister
|
| • |
Stuck open or leaking EVAP purge valve
|
| • |
Restricted exhaust
|
| • |
Incorrect PCV system operation
|
| • |
If you find any of the above conditions, repair as necessary.
|
| 4. |
Refer to
Road Test Warning
.
Operate the vehicle within the Conditions for Running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observed from the Freeze Frame/Failure Records data. |
|||||||
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
