PRE-RELEASE
DTC B1529
| DTC B1529 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptors |
DTC B1529 03
Control Module Voltage Reference Output 5 Circuit Low Voltage
DTC B1529 07
Control Module Voltage Reference Output 5 Circuit High Voltage
| Diagnostic Fault Information |
Electrical DTCs
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
| 12V Reference | B1529 03, B1405 03 | 1 | B1529 07 | B1529 07 |
| Steering Wheel Control Switch Signal | 1 | 1 | B3622 07 | - |
| 1. Steering Wheel Controls Inoperative | ||||
| Circuit/System Description |
The body control module (BCM) supplies voltage to the steering wheel control switches and monitors the return signal. Each switch state is associated to a set resistance value and when pressed a specific voltage drop occurs across the resistor unique to the switch. The BCM identifies the switch selection and activates the feature.
| Conditions for Running the DTC |
| • |
The system voltage is between 9-16 V.
|
|
| • |
The ignition is ON.
|
|
| Conditions for Setting the DTC |
B1529 03
| • |
The BCM detects a short to ground in the 12 V reference circuit.
|
|
| • |
The above condition is present for greater than 30 s.
|
|
B1529 07
| • |
The BCM detects a short to voltage in the 12 V reference circuit.
|
|
| • |
The above condition is present for greater than 30 seconds.
|
|
| Action Taken When the DTC Sets |
The BCM will ignore switch inputs.
| Conditions for Clearing the DTC |
| • |
The condition responsible for setting the DTC no longer exists.
|
|
| • |
A history DTC will clear once 100 consecutive malfunction free ignition cycles have occurred.
|
|
| Reference Information |
Schematic Reference
Steering Wheel Secondary/Configurable Control Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Steering Wheel Controls Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Testing |
| 1. |
Ignition OFF, disconnect the S70R Steering Wheel Controls Switch - Right.
|
|
| 2. |
Ignition ON, test for greater than 11 V between the voltage reference circuit terminal 1 and ground.
|
|
| 3. |
If less than the specified value, test the voltage reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 body control module.
|
|
| 4. |
Test for greater than 11 V between the voltage reference circuit terminal 1 and the signal circuit terminal 2.
|
|
| 5. |
If less than the specified value, test the signal circuit for a short to voltage or an open/high resistance. If the circuit tests normal, replace the K9 body control module.
|
|
| 6. |
Ignition OFF, disconnect the X3 harness connector at the K9 Body Control Module.
|
|
| 7. |
Test for infinite resistance between the signal circuit terminal 2 at the S70R Steering Wheel Controls Switch - Right and ground.
|
|
| 8. |
If less than the specified value, test the signal circuit for a short to ground.
|
|
| 9. |
If all circuits test normal, test or replace the S70R Steering Wheel Controls Switch - Right.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for BCM replacement, setup, and programming
