PRE-RELEASE
DTC B257B
| DTC B257B |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptors |
DTC B257B 03
Lighting Control Switch Signal Low Voltage
DTC B257B 07
Lighting Control Switch Signal High Voltage
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
| Headlamp Switch B+ Reference | B257B 03* | B257B 03* | - | - |
| Instrument Panel Lamps Dimmer Switch Signal | B257B 03* | B257B 03* | B257B 07* | - |
| * Interior backlighting at full intensity and cannot be dimmed | ||||
| Circuit/System Description |
The body control module (BCM) supplies a reference voltage to the backlight dimmer switch, which is part of the headlamp switch. When the backlight dimmer switch is placed in a desired brightness position, reference voltage is applied to the BCM. The BCM interprets this voltage signal, then applies a pulse width modulated (PWM) voltage to the LED dimming supply circuit to all related interior lamps, illuminating them to the desired level of brightness.
| Conditions for Running the DTC |
The ignition is ON.
| Conditions for Setting the DTC |
B257B 03
The BCM detects a voltage that is lower than 0.3 V on the dimming voltage circuit.B257B 07
The BCM detects a voltage that is greater than 12.2 V on dimming voltage circuit.| Action Taken When the DTC Sets |
The BCM will not dim or illuminate any LED backlighting supplied by the backlight lamp control circuits.
| Conditions for Clearing the DTC |
| • |
The condition responsible for setting the DTC no longer exists.
|
|
| • |
A history DTC will clear once 100 consecutive malfunction ignition cycles have occurred.
|
|
| Reference Information |
Schematic Reference
Interior Lights Dimming Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Interior Lighting Systems Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Verification |
Ignition ON, headlamps ON, vary the interior backlight dimming from low to full bright by using the dimmer switch. The interior backlighting should start dim and then become full bright.
| Circuit/System Testing |
| 1. |
Ignition OFF, disconnect the harness connector at the S30 Headlamp Switch.
|
|
| 2. |
Ignition ON, test for B+ between the B+ reference circuit terminal 1 and ground.
|
|
| 3. |
If less than the specified range, test the B+ reference circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
|
|
| 4. |
Ignition ON, test for less than 0.3 V between signal circuit terminal 12 and ground.
|
|
| 5. |
If greater than the specified range, test the signal circuit pin 12 for a short to voltage. If the circuit tests normal, replace the BCM K9.
|
|
| 6. |
Reconnect the harness connector at the S30 Headlamp Switch.
|
|
| 7. |
Dim the interior backlighting with the S30 Headlamp Switch.
|
|
| 8. |
Disconnect the harness connector at the S30 Headlamp Switch.
|
|
| 9. |
Install a 3 A fused jumper wire between the signal circuit terminal 12 and the B+ reference circuit terminal 1. The interior backlighting should now be dimmed.
|
|
| 10. |
If the interior backlighting is not dimmed, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K9 BCM.
|
|
| 11. |
If all circuits test normal, replace the S30 Headlamp Switch.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Headlamp Switch Replacement
|
|
| • |
Control Module References
for BCM replacement, programming and setup
|
|
