PRE-RELEASE
DTC B1451
| DTC B1451 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptors |
DTC B1451 01
Accessory Power Circuit Short to Voltage
DTC B1451 02
Accessory Power Circuit Short to Ground
DTC B1451 04
Accessory Power Circuit Open/High Resistance
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
| Accessory Wakeup Serial Data | B1451 02 | B1451 04 | B1451 01 | - |
| Circuit/System Description |
The keyless entry control module provides backup control for the accessory wakeup serial data circuit by applying voltage to the circuit. The accessory wakeup serial data circuit is energized when the ignition mode switch is in ACC or RUN.
| Conditions for Running the DTC |
B1451 01, B1451 04
| • |
Vehicle power mode is OFF or Crank Request.
|
|
| • |
Module is awake.
|
|
| • |
DTC B1451 not already set.
|
|
| • |
System voltage is 6-16 V.
|
|
B1451 02
| • |
Vehicle power mode is ACC or RUN.
|
|
| • |
Module is awake.
|
|
| • |
Output is active.
|
|
| • |
DTC B1451 is not already set.
|
|
| • |
System voltage is 6-16 V.
|
|
| Conditions for Setting the DTC |
B1451 01
Accessory output is not active and a short to battery is detected 3 consecutive times.B1451 02
Accessory output is active and a short to ground is detected 3 consecutive times.B1451 04
Accessory output is not active and an open circuit is detected 20 consecutive times.| Action Taken When the DTC Sets |
B1451 02
The accessory output is deactivated when a short to ground is detected. After 100 ms the output is activated again. This happens 3 times and then the output is deactivated until a new accessory request is received.B1451 01, B1451 04
No action is taken.| Conditions for Clearing the DTC |
| • |
The current DTC will clear when the malfunction is no longer present during a DTC check.
|
|
| • |
A history DTC will clear after 40 malfunction free ignition cycles.
|
|
| Diagnostic Aids |
| • |
A short to voltage on the accessory wakeup serial data circuit will keep the vehicle serial data bus awake, which can drain the vehicle"s battery.
|
|
| • |
If DTC B1451 02 is set, be sure to test the accessory wakeup serial data circuit for a short to ground between the body control module (BCM) and each of the modules that receive a signal from the accessory wakeup circuit before replacing the BCM. A short to ground between the BCM and modules may provide feedback through the BCM to the keyless entry control module and result in the setting of the DTC.
|
|
| Reference Information |
Schematic Reference
| • |
Body Control System Schematics
|
|
| • |
Power Distribution Schematics
|
|
Connector End View Reference
Component Connector End Views
Description and Operation
Power Mode Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References
| Circuit/System Testing |
| 1. |
Verify DTC B1330 is not set.
|
|
| 2. |
If the DTC is set, refer to
DTC B1325, B1330, B1517, C0800, P0560, P0562, or P0563
.
|
|
| 3. |
Ignition OFF, disconnect the X2 harness connector at the K84 keyless entry control module.
|
|
| 4. |
Verify that a test lamp illuminates between B+ circuit terminal 5 and ground.
|
|
| 5. |
If the test lamp does not illuminate, test the B+ circuit for an open/high resistance. If the B+ fuse is open, test the B+ circuit for a short to ground.
|
|
| 6. |
Connect the X2 harness connector at the K8 keyless entry control module. Disconnect the X3 harness connector at the K 9 BCM.
|
|
| 7. |
Ignition OFF, test for less than 1 V between the ignition circuit terminal 5 and ground.
|
|
| 8. |
If greater than the specified range, test the ignition circuit for a short to voltage. If the circuit tests normal, replace the K84 keyless entry control module.
|
|
| 9. |
Ignition ON, verify that a test lamp illuminates between the ignition circuit terminal 5 and ground.
|
|
| 10. |
If the test lamp does not illuminate, test the ignition circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K84 keyless entry control module.
|
|
| 11. |
If all circuits test normal, replace the K9 body control module.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References
