DTC B0081 (Passenger Presence Module)
|
|
DTC B0081 (Passenger Presence Module)
|
DTC B0081 11
Passenger Presence Module High Input
DTC B0081 4B
Passenger Presence Module Calibration Not Learned
|
Circuit/System Description
|
When the ignition is turned ON, the inflatable restraint sensing and diagnostic module (SDM) and the passenger presence module perform tests to diagnose critical malfunctions. Upon a successful power-up mode the SDM will illuminate both PASSENGER AIRBAG ON/OFF indicators. If the SDM detects a fault in the passenger presence module, it may disable the passenger instrument panel air bag deployment loop, set DTC B0081 and illuminate the AIRBAG indicator.
|
Conditions for Running the DTC
|
Ignition voltage is between 9-16 V.
|
Conditions for Setting the DTC
|
Any of the following conditions must exist for 5 seconds.
B0081 11
The passenger presence module has failed the preload procedure.
B0081 4B
The passenger presence module is not calibrated.
|
Action Taken When the DTC Sets
|
|
•
|
The SDM requests the instrument cluster to illuminate the AIR BAG indicator.
|
|
•
|
The passenger instrument panel air bag deployment loop will be disabled.
|
|
Conditions for Clearing the DTC
|
|
•
|
The condition responsible for setting the DTC no longer exists.
|
|
•
|
A history DTC will clear once 100 malfunction-free ignition cycles have occurred.
|
|
•
|
If either the SDM or PPS were replaced verify that the correct part numbers were used for the vehicle application.
|
|
•
|
If this DTC is set as either current or history it may have been caused by an electronic device. If an electronic device (Computers, MP3 Players, Cell Phones, Diagnostic Scan Tool, etc.) was placed on the passenger seat the passenger presence module may command the passenger air bag indicator to turn on and/or command the passenger seat belt indicator to turn on. Make sure there are no objects on the passenger seat and clear the DTCs. If this DTC returns then perform this diagnostic. If the DTC does not reset there is no further work needed on the passenger presence system.
|
|
•
|
If this DTC is set as either current or history it may have been caused by an aftermarket seat heater. The aftermarket seat heater may command the passenger air bag indicator to turn on and/or command the passenger seat belt indicator to turn on. Remove the aftermarket seat heater from the passenger seat and clear the DTCs. If this DTC returns then perform this diagnostic. If the DTC does not reset there is no further work needed on the passenger presence system.
|
Description and Operation
SIR System Description and Operation
Scan Tool Reference
Control Module References
for scan tool information
|
Circuit/System Verification
|
|
Note
|
|
•
|
This system is serviced as a kit (seat foam, module and sensing mat). Perform a passenger presence system preload procedure whenever a component is replaced. Refer to
Passenger Presence System Programming and Setup
.
|
|
•
|
Both SDM and passenger presence module set DTC B0081 but with different symptoms bytes. Therefore it is important to identify which module has set the DTC B0081. Use the symptom bytes as a way of identify the correct module to diagnose.
|
|
•
|
The SDM sets a B0081 3A when an incorrect passenger presence module is installed.
|
|
1.
|
Verify that DTC B0081 3A is not set in the SDM.
|
|
2.
|
|
Note
|
|
The SDM sets a redundant B0081 00 DTC when the passenger presence module sets a DTC B0081 11 or B0081 4B.
|
Verify that DTC B0081 11 or DTC B0081 4B is not set in the passenger presence module.
|
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.
Control Module References
for passenger presence system or SDM replacement, programming and setup
