PRE-RELEASE
DTC B2516
| DTC B2516 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptor |
DTC B2516 00
Driver Exterior Door Lock Switch Circuit, Malfunction.
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
| Driver Door Lock Switch Signal | B2516 00 | 1 | 1 | - |
| Driver Door Handle Ground | - | 1 | - | - |
| 1. Exterior Door Lock Switch Malfunction | ||||
| Circuit/System Description |
The exterior driver door handle contains a small sensor which allows the driver to lock the vehicle doors from the outside without using the remote keyless transmitter. The keyless remote control sends a 12 V signal to the driver's door handle switch signal circuit, when the sensor is moved, signal circuit is ground and the voltage drops. The remote control module detects the voltage drop and then sends a serial data message to BCM which orders all doors to be locked.
| Conditions for Running the DTC |
The transition from shutoff to run.
| Conditions for Setting the DTC |
The keyless entry control module detects the driver door lock switch signal circuit is shorted to ground for greater than 45 seconds.
| Action Taken When the DTC Sets |
The keyless entry control module ignores inputs from the left front exterior door handle switch.
| Conditions for Clearing the DTC |
| • |
The DTC will be current for as long as the fault is present.
|
|
| • |
When the fault is no longer present, the DTC will be a history DTC.
|
|
| • |
A history DTC will clear after 50 ignition cycles.
|
|
| Reference Information |
Schematic Reference
Remote Function Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Power Door Latch Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Verification |
Ignition ON, observe the scan tool Exterior Driver Door Handle Proximity Sensor parameter while pressing and releasing the driver door handle lock switch. The value should change between Active and Inactive as the switch is pressed and released.
| Circuit/System Testing |
| 1. |
With the ignition OFF, disconnect the connector from A24D exterior door handle unit on the driver's side.
|
|
| 2. |
Test for less than 5 Ω between the ground circuit pin 4 and ground.
|
|
| 3. |
If greater than the specified range, test the ground circuit for open/high resistance.
|
|
| 4. |
Check with the diagnostic tool that the door handle system is Inactive.
|
|
| 5. |
If not the specified value, test the signal circuit terminal 3 with respect to short to ground. If the circuit tests normal, replace the K84 keyless entry control module.
|
|
| 6. |
Connect a 3A jumper between the signal circuit terminal 3 and ground, verify with the diagnostic tool that the door handle system is Activate.
|
|
| 7. |
If not the specified value, test the signal circuit for short to voltage or open/high resistance. If the circuit tests normal, replace the K84 keyless entry control module.
|
|
| 8. |
If all circuits test normal, check or replace A24D exterior door handle on the driver's side.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Front Side Door Outside Handle Replacement
|
|
| • |
Control Module References
for keyless entry control module replacement, setup, and programming
|
|
