PRE-RELEASE
DTC B3122
| DTC B3122 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptors |
DTC B3122 02
Keyless Entry Antenna 4 Short to Ground
DTC B3122 05
Keyless Entry Antenna 4 High Voltage/Open
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
| Keyless Entry Antenna Signal - Center Console Front | B3122 02 | B3122 05 | B3122 05 | - |
| Keyless Entry Antenna Low Reference - Center Console Front | - | B3122 05 | - | - |
| Circuit/System Description |
The front center console antenna is located in front of the center console assembly and is used to establish low frequency communications with the keyless entry transmitter. When the driver attempts to change the ignition status of the vehicle, the keyless entry control module communicates with the front center console antenna.
| Conditions for Running the DTC |
| • |
The touch pad in the driver door or passenger door handle is touched within 15 minutes of any door ajar status changing.
|
|
| • |
The last door becomes closed.
|
|
| • |
Pressing the start/stop switch.
|
|
| Conditions for Setting the DTC |
B3122 02
The keyless entry control module detects a short to ground on the front center console keyless entry antenna signal circuit.B3122 05
The keyless entry control module detects a short to B+ or an open on the front center console keyless entry antenna signal circuit.| Action Taken When the DTC Sets |
Vehicle will not detect the transmitter in some locations inside the vehicle. If the transmitter is not detected then vehicle will not change ignition modes when start/stop button is pressed.
| Conditions for Clearing the DTC |
| • |
A current DTC will clear when the conditions for setting the DTC are no longer present.
|
|
| • |
A history DTC will clear after 40 malfunction-free ignition cycles.
|
|
| Reference Information |
Schematic Reference
Remote Function Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Keyless Entry System Description and Operation (without ATH) Keyless Entry System Description and Operation (with ATH)
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Testing |
| 1. |
Ignition OFF, disconnect the harness connector at the T10J center console front keyless entry antenna.
|
|
| 2. |
Ignition ON, test for less than 1 V between the signal circuit terminal 1 and ground.
|
|
| 3. |
If greater than the specified range, test the signal circuit for a short to voltage. If the circuit tests normal, replace the K84 keyless entry control module.
|
|
| 4. |
Ignition OFF, install a DMM between the signal circuit terminal 1 and ground. Set the DMM to capture DC voltage using the MIN MAX function. |
|||||||
| 5. |
Activate the antenna by pressing the ignition mode switch. Verify the MAX voltage captured by the DMM is greater than 1.0 V.
|
|
| 6. |
If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, replace the K84 keyless entry control module.
|
|
| 7. |
Test for less than 1 V between the low reference circuit terminal 2 and ground.
|
|
| 8. |
If greater than the specified range, test the low reference circuit for a short to voltage. If the circuit tests normal, replace the K84 keyless entry control module.
|
|
| 9. |
Install a DMM between the signal circuit terminal 1 and the low reference circuit terminal 2. Set the DMM to capture DC voltage using the MIN MAX function. |
|||||||
| 10. |
Activate the antenna by pressing the ignition mode switch. Verify the MAX voltage captured by the DMM is greater than 1.0 V.
|
|
| 11. |
If less than the specified range, test the low reference circuit for an open circuit/high resistance. If the circuit tests normal, replace the K84 keyless entry control module.
|
|
| 12. |
If the test results for all circuits are normal, replace the T10J front keyless entry antenna in the center console. Verify that DTC B3122 is not set.
|
|
| 13. |
If the DTC is set, replace the K84 keyless entry control module.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Ignition Lock Key Transmitter Antenna Replacement - Instrument Panel
|
|
| • |
Control Module References
for keyless entry control module replacement, setup, and programming
|
|
