DTC B316B, B317A, B318A, or B319A
|
|
DTC B316B, B317A, B318A, or B319A
|
DTC B316B 00
Driver Window Switch
DTC B316B 02
Driver Window Switch Short to Ground
DTC B316B 39
Driver Window Switch Internal Malfunction
DTC B317A 02
Passenger Window Switch Short to Ground
DTC B317A 39
Passenger Window Switch Internal Malfunction
DTC B318A 02
Left Rear Window Switch Short to Ground
DTC B318A 39
Left Rear Window Switch Internal Malfunction
DTC B319A 02
Right Rear Window Switch Short to Ground
DTC B319A 39
Right Rear Window Switch Internal Malfunction
|
Diagnostic Fault Information
|
|
Circuit
|
Short to Ground
|
Open/High Resistance
|
Short to Voltage
|
Signal Performance
|
|
Driver Window Motor Control
|
B316B 02
|
1
|
1
|
-
|
|
Left Rear Window Motor Control
|
3
|
3
|
3
|
-
|
|
Right Front Window Motor Control
|
4
|
4
|
4
|
-
|
|
Passenger Window Motor Control
|
B317A 02
|
2
|
2
|
-
|
|
1. Driver Window Malfunction
2. Passenger Window Malfunction
3. Left Rear Window Malfunction
4. Right Rear Window Malfunction
|
|
Circuit/System Description
|
When a switch is pressed on the driver window switch panel, a serial data message is sent to the body control module (BCM). The BCM examines the request and checks for messages from other power window motors which prohibit the window movement. If no prohibitive messages have been received, the BCM will send a serial data message to the passenger window motor or to the appropriate rear window switch which will perform the command as requested.
|
Conditions for Running the DTC
|
Battery voltage must be between 9-16 V.
|
Conditions for Setting the DTC
|
B316B 00
The BCM has detected the driver right front or left rear or right rear window switch is active for greater than 60 seconds.
B316B 02
The BCM has detected the driver left front window switch is active for greater than 60 seconds.
B317A 02
The BCM has detected the passenger window switch is active for greater than 60 seconds.
B318A 02
The BCM has detected the left rear window switch is active for greater than 60 seconds
B319A 02
The BCM has detected the right rear window switch is active for greater than 60 seconds
B316B 39, B317A 39, B318A 39, B319A 39
The BCM has detected an internal failure within the affected door switch
|
Action Taken When the DTC Sets
|
The affected power window will malfunction.
|
Conditions for Clearing the DTC
|
B316B 00, B316B 02, B317A 02, B318A 02, B319A 02
|
•
|
The DTC will be current for as long as the fault is present.
|
|
•
|
The DTC will change from current to history when the fault is no longer present.
|
|
•
|
A history DTC will clear after 100 consecutive ignition cycles if the condition for the malfunction is no longer present.
|
B316B 39, B317A 39, B318A 39, B319A 39
If the DTC is current, the affected window switch must be replaced before the DTC can be cleared.
Schematic Reference
Moveable Window Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Power Windows Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References
for scan tool information
|
Circuit/System Verification
|
|
1.
|
Ignition ON, verify that each of the scan tool parameters listed below are Inactive:
|
|
|
•
|
Front Passenger Main Control Down Switch
|
|
|
•
|
Front Passenger Main Control Express Switch
|
|
|
•
|
Front Passenger Main Control Up Switch
|
|
|
•
|
Left Rear Window Main Control Down Switch
|
|
|
•
|
Left Rear Window Main Control Express Switch
|
|
|
•
|
Left Rear Window Main Control Up Switch
|
|
|
•
|
Right Rear Window Main Control Down Switch
|
|
|
•
|
Right Rear Window Main Control Express Switch
|
|
|
•
|
Right Rear Window Main Control Up Switch
|
|
2.
|
If any of the parameters are always Active, replace the S79D window switch-driver.
|
|
3.
|
Verify that the scan tool Left Rear Window Switch at Door parameter is Inactive.
|
|
4.
|
If not the specified value, replace the S79LR window switch-left rear.
|
|
5.
|
Verify that the scan tool Right Rear Window Switch at Door parameter is Inactive.
|
|
6.
|
If not the specified value, replace the S79RR window switch-right rear.
|
|
7.
|
Command the driver window to go UP, DOWN, express UP and express DOWN by using the S79D window switch-driver. The driver window should perform the UP, DOWN, express UP and express DOWN functions.
|
|
8.
|
If the driver window does not perform as specified, refer to Driver Window Switch Malfunction.
|
|
9.
|
Command the passenger window to go UP, DOWN, express UP and express DOWN by using the S79P window switch-passenger. The passenger window should perform the UP, DOWN, express UP and express DOWN function.
|
|
10.
|
If the passenger window does not perform as specified, refer to Passenger Window Malfunction.
|
Driver Window Switch Malfunction
|
1.
|
Ignition OFF, disconnect the harness connector at the S79D window switch-driver.
|
|
2.
|
Ignition ON, verify that the scan tool Driver Window Main Control Down Switch parameter is Inactive.
|
|
3.
|
If not the specifed value, test the control circuit terminal 3 for a short to ground. If the circuit tests normal, test or replace the M74D window motor-driver.
|
|
4.
|
Verify that the scan tool Driver Window Main Control Up Switch parameter is Inactive.
|
|
5.
|
If not the specifed value, test the control circuit terminal 6 for a short to ground. If the circuit tests normal, test or replace the M74D window motor-driver.
|
|
6.
|
Verify that the scan tool Driver Window Main Control Express Switch parameter is Inactive.
|
|
7.
|
If not the specifed value, test the control circuit terminal 2 for a short to ground. If the circuit tests normal, test or replace the M74D window motor-driver.
|
|
8.
|
If all circuits test normal, test or replace the S79D window switch-driver.
|
Passenger Switch Window Malfunction
|
1.
|
Ignition OFF, disconnect the harness connector at the S79P window switch-passenger.
|
|
2.
|
Ignition ON, test for greater than 10V between the signal circuit terminal listed below and ground:
|
|
|
•
|
Signal circuit terminal 6
|
|
|
•
|
Signal circuit terminal 7
|
|
|
•
|
Signal circuit terminal 8
|
|
3.
|
If less than the specified range, test the signal circuit for a short to ground or an open/high resistance. If the circuit tests normal, test or replace the M74P window motor-passenger.
|
|
4.
|
If all circuits test normal, test or replace the S79P window switch-passenger.
|
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.
