PRE-RELEASE
Stabilizer Shaft Insulator Replacement (GNC)
| Stabilizer Shaft Insulator Replacement (GNC) |
| Removal Procedure |
| 1. |
Raise and support the vehicle. Refer to
Lifting and Jacking the Vehicle
.
|
|
| 2. |
Remove the tire and wheel assembly. Refer to
Tire and Wheel Removal and Installation
.
|
|
| 3. |
Remove the rear muffler assembly. Refer to
Exhaust System Replacement (LDK/A20NHT - FWD)
Exhaust System Replacement (LAU/A28NER)
Exhaust System Replacement (LDK/A20NHT-AWD, LAU/A28NER-AWD )
.
|
|
| 4. |
Remove the fasteners from the trailing arm to body. Refer to
Trailing Arm Replacement
.
|
|
| 5. |
Remove the rear spring. Refer to
Rear Spring Replacement (GNC)
Rear Spring Replacement (GNE)
.
|
|
| 6. |
Remove the park brake cables from the trailing arms. Refer to
Parking Brake Rear Cable Replacement (J71)
.
|
|
| 7. |
Without disconnecting the hydraulic brake hose from the caliper, remove and support the brake caliper. Refer to
Rear Brake Caliper Replacement (J60)
Rear Brake Caliper Replacement (J61, J62)
|
|
| 8. |
Remove lower fastener shock absorber. Refer to
Shock Absorber Replacement (GNC)
Shock Absorber Replacement (GNE)
.
|
|
| 9. |
Support and secure adjustable jack stands to the rear support.
|
|
| 10. |
Mark up support position to body with spray paint.
|
|
| 11. |
Remove the mounting bolts (1) for the support. Refer to
Support Replacement (GNC)
Support Replacement (GNE)
Support Replacement (GNE, AWD)
.
|
|
| 12. |
Lower the support enough to gain access to the rear stabilizer shaft insulator clamps mounting bolts.
|
|
| 13. |
Remove the stabilizer shaft (1) from the stabilizer shaft link (2).
|
|
| 14. |
Remove the bracket bolt (1), the bracket (2) and the insulator (3). 
|
|||||||
| Installation Procedure |
| 1. |
Install the insulator (3), the bracket (2), on the stabilizer shaft (4).
|
|
| 2. |
Refer to
Fastener Caution
.
Install the bolts (1). Tighten the clamp bolt (1) to 22 Nm (16 lb ft) + 30 grader . |
|
| 3. |
Install the stabilizer shaft (1) to stabilizer shaft link (2) and tighten to
50 Nm (37 lb ft)
.
|
|
| 4. |
Raise the rear support back into position.
|
|
| 5. |
Install the rear support bolts (1). Refer to
Support Replacement (GNC)
Support Replacement (GNE)
Support Replacement (GNE, AWD)
.
|
|
| 6. |
Install the lower shock absorber mounting bolts. Refer to
Shock Absorber Replacement (GNC)
Shock Absorber Replacement (GNE)
.
|
|
| 7. |
Install the rear brake calipers. Refer to
Rear Brake Caliper Replacement (J60)
Rear Brake Caliper Replacement (J61, J62)
|
|
| 8. |
Install the fasteners from the trailing arm to body. Refer to
Trailing Arm Replacement
.
|
|
| 9. |
Install the rear springs. Refer to
Rear Spring Replacement (GNC)
Rear Spring Replacement (GNE)
.
|
|
| 10. |
Remove the adjustable jack stands from the rear support.
|
|
| 11. |
Install the park brake cables on the trailing arms. Refer to
Parking Brake Rear Cable Replacement (J71)
.
|
|
| 12. |
Install the rear muffler assembly. Refer to
Exhaust System Replacement (LDK/A20NHT - FWD)
Exhaust System Replacement (LAU/A28NER)
Exhaust System Replacement (LDK/A20NHT-AWD, LAU/A28NER-AWD )
.
|
|
| 13. |
Install the tire and wheel assembly. Refer to
Tire and Wheel Removal and Installation
.
|
|
| 14. |
Lower the vehicle.
|
|
