PRE-RELEASE
DTC P0722
| DTC P0722 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptor |
DTC P0722
Output Speed Sensor Circuit No Signal
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
|
Output Shaft Sensor Supply Voltage
|
-
|
-
|
-
|
-
|
|
Output Shaft Sensor Signal
|
P0722
|
P0722
|
P0722
|
-
|
| Typical Scan Tool Data |
Transmission Output Shaft Sensor
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage |
|
Operating Conditions:
Engine running, normal operating temperature
Parameter Normal Range: 0-7 000 RPM |
|||
|
Output Shaft Sensor Supply Voltage
|
Out of Range
|
Out of Range
|
OK
|
|
Output Shaft Sensor Signal
|
0 RPM
|
0 RPM
|
0 RPM
|
| Circuit/System Description |
The output shaft sensor is a hall-effect type sensor. The sensor faces the output shaft machined teeth surface. As the output shaft rotates, the sensor produces a signal frequency based on the machined surface of the output shaft. This signal is transmitted to the transmission control module (TCM). The TCM uses the output shaft sensor signal in connection with the input speed sensor signal to control engine torque, shift timing, and lock-up.
| Conditions for Running the DTC |
P0722
| • |
The ignition voltage is 10.2-15.5 V.
|
|
| • |
The engine speed is greater than 400 RPM for 2 s.
|
|
| • |
The transmission is not in emergency mode.
|
|
| • |
TCM communication is normal.
|
|
| • |
Driving in D range.
|
|
| Conditions for Setting the DTC |
P0722
| • |
Deviation from calculated output speed is more than 300 RPM.
|
|
| • |
No output speed sensor pulse while receiving pulses on the input speed sensor.
|
|
| • |
No output speed sensor pulse when vehicle speed from ABS is more than 20 km/h (13 MPH) for 300 ms.
|
|
| Action Taken When the DTC Sets |
| • |
DTC P0722 is Type A DTC.
|
|
| • |
The TCM freezes transmission adaptive functions.
|
|
| • |
The TCM turns OFF all solenoids.
|
|
| • |
The TCM allows the vehicle after a stop to operate only in the second gear and “R” range.
|
|
| Conditions for Clearing the DTC |
| • |
DTC P0722 is Type A DTC.
|
|
| • |
Output speed is greater than 300 RPM for more than 70 s.
|
|
| • |
Deviation from calculated output speed is less than 5% for more than 1 s.
|
|
| Diagnostic Aids |
| • |
Damage or misalignment of the counter drive gear machined teeth surface may cause a speed sensor malfunction.
|
|
| • |
Proper torque of the output shaft sensor mounting bolt is critical to proper output shaft sensor operation.
|
|
| Reference Information |
Schematic Reference
Automatic Transmission Controls Schematics
Connector End View Reference
Component Connector End Views
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
Description and Operation
Transmission Component and System Description
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Verification |
| 1. |
Operate the vehicle at 16-32 km/h (10-20 MPH) while observing the scan tool Transmission OSS parameter. The Transmission OSS should vary with the vehicle speed and not drop out.
|
|
| 2. |
Operate the vehicle within the conditions for running the DTC to verify the DTC does not reset. You may also operate the vehicle within the conditions that you observe from the Freeze Frame/Failure Records data.
|
|
| Circuit/System Testing |
Static Test
| 1. |
Ignition OFF, remove the K71 Transmission Control Module.
|
|
| 2. |
Test for more than 1 MΩ between the low reference circuit terminal 20 X2 and the voltage supply circuit terminal 19 X2.
|
|
| 3. |
If less than the specified range, test the wiring harness for internal short. If the circuit tests normal, replace the automatic transmission.
|
|
| 4. |
Test for infinite resistance between each terminal and the low reference circuit terminal 20 X2 and also to the voltage supply circuit terminal 19 X2.
|
|
| 5. |
If less than the specified range, replace the wiring harness.
|
|
| 6. |
If all circuits test normal, test or replace the K71 Transmission Control Module. Verify the DTC does not reset.
|
|
| 7. |
If the DTC resets, replace the automatic transmission.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Control valve body replacement-Refer to
Control Valve Body Replacement
.
|
|
| • |
Wiring harness-Refer to
Automatic Transmission Wiring Harness Replacement
.
|
|
| • |
TCM-Refer to
Control Module References
.
|
|
| • |
Perform the
Transmission Adaptive Functions
.
|
|
