PRE-RELEASE
DTC B0082
| DTC B0082 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptors |
DTC B0082 01
Seat Belt Reminder Sensor Short to Battery
DTC B0082 02
Seat Belt Reminder Sensor Short to Ground
DTC B0082 04
Seat Belt Reminder Sensor Open Circuit
| Diagnostic Fault Information |
| Circuit | Short to Ground | Open/High Resistance | Short to Voltage | Signal Performance |
| Seat Belt Reminder Sensor Signal | B0082 02 | B0082 04 | B0082 01 | - |
| Seat Belt Reminder Sensor Ground | - | B0082 04 | B0082 04 | - |
| Circuit/System Description |
The seat belt reminder sensor is in the passenger seat cushion and provides an input to the inflatable restraint sensing and diagnostic module (SDM). The SDM supplies a low reference circuit and a seat belt reminder sensor signal circuit to determine whether or not the seat is occupied.
| Conditions for Running the DTC |
Ignition voltage is between 9-16 V.
| Conditions for Setting the DTC |
B0082 01
The SDM detects a short to voltage in the seat belt reminder sensor signal circuit.B0082 02
The SDM detects a short to ground in the seat belt reminder sensor signal circuitB0082 04
The SDM detects an open/high resistance in the seat belt reminder sensor signal circuit or the seat belt reminder sensor ground circuit| Action Taken When the DTC Sets |
The SIR System is disabled and no deployments are allowed.
| Conditions for Clearing the DTC |
| • |
The DTC will be current for as long as the fault is present
|
|
| • |
When the fault is no longer present, the DTC will be a history DTC
|
|
| • |
A history DTC will clear after 50 ignition cycles
|
|
| Reference Information |
Schematic Reference
SIR Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
SIR System Description and Operation
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
| • |
Connector Repairs
|
|
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Verification |
| 1. |
Ignition ON, with the passenger seat unoccupied, verify the scan tool Passenger Seat Occupancy Status parameter is Empty Seat.
|
|
| 2. |
With the passenger seat occupied, verify the scan tool Passenger Seat Occupancy Status parameter is Occupied.
|
|
| Circuit/System Testing |
| 1. |
Ignition OFF.
|
|
| 2. |
Disconnect the harness connector at the B60 seat belt reminder sensor.
|
|
| 3. |
Test for less than 30 Ω between the ground circuit terminal 2 and ground.
|
|
| 3.1. |
Ignition OFF, disconnect the harness connector at the K36 SDM.
|
| 3.2. |
Test for less than 2 Ω in the passenger air bag disable switch ground circuit end to end.
|
| 4. |
Ignition ON, test for 4.75-5.25 V between the signal circuit terminal 1 and ground.
|
|
| 4.1. |
Disconnect the harness connector at the K36 SDM.
|
| 4.2. |
Test for infinite resistance between the signal circuit and ground.
|
| 4.3. |
Test for less than 2 Ω in the signal circuit end to end.
|
| 4.1. |
Ignition OFF.
|
| 4.2. |
Disconnect the harness connector at the K36 SDM.
|
| 4.3. |
Ignition ON.
|
| 4.4. |
Test for less than 1 V between the signal circuit and ground.
|
| 5. |
Replace the B60 seat belt reminder sensor.
|
|
| Repair Instructions |
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
| • |
Inflatable Restraint Front Passenger Presence Sensor Replacement
|
|
| • |
Control Module References
for SDM replacement, setup, and programming
|
|
