DTC B3205, B3210, B3215, or B3220
|
|
DTC B3205, B3210, B3215, or B3220
|
DTC B3205 00
Driver Window Motor Circuit
DTC B3205 39
Driver Window Motor Circuit internal electronic failure
DTC B3205 42
Driver Window Motor Circuit calibration data set not programmed
DTC B3205 4B
Driver Window Motor Circuit calibration not learned
DTC B3210 00
Right Front/Passenger Window Motor Circuit
DTC B3210 39
Right Front/Passenger Window Motor Circuit internal electronic failure
DTC B3210 42
Right Front/Passenger Window Motor Circuit calibration data set not programmed
DTC B3210 4B
Right Front/Passenger Window Motor Circuit calibration not learned
DTC B3215 39
Left Rear Window Motor Circuit internal electronic failure
DTC B3220 39
Right Rear Window Motor Circuit internal electronic failure
|
Circuit/System Description
|
When a switch is pressed on the driver window switch panel, a serial data message is sent to the body control module (BCM). The BCM examines the request and checks for messages from other power window motors which prohibit the window movement. If no prohibitive messages have been received, the BCM will send a serial data message to the passenger window motor or to the appropriate rear window switch which will perform the command as requested.
|
Conditions for Running the DTC
|
|
•
|
The ignition switch is in the ON position
|
|
•
|
Battery voltage must be between 9-16 V.
|
|
Conditions for Setting the DTC
|
B3205 00, B3210 00
The BCM has detected that the compatibility code stored in the affected window motor does not match the compatibility code stored in the BCM.
B3205 39, B3210 39, B3215 39, B3220 39
An internal malfunction has been detected by the BCM in the power window motor while commanding the window UP or DOWN.
B3205 42, B3210 42
The BCM will automatically attempt to download the calibration program into the appropriate window motor (As will occur when the window motor has been replaced), if the first calibration program fails to load, the BCM will attempt to download the calibration program a second time. If this download fails, the BCM will set appropriate DTC.
B3205 4B, B3210 4B
The BCM detects that a window motor is "not normalized" which will occur under the following conditions:
|
•
|
When the battery has been disconnected
|
|
•
|
When the battery has been replaced
|
|
•
|
When the door wiring harness has been disconnected
|
|
•
|
When the window motor has been disconnected.
|
|
Action Taken When the DTC Sets
|
B3205 00, B3205 39, B3205 42, B3210 00, B3210 39, B3210 42, B3215 39, B3220 39
The affected motor will be inoperative.
B3205 4B, B3210 4B
The affected motor will not perform the express up or express down functions and the driver information center will display Open, then Close Driver Window or will display Open, then Close Passenger Window.
|
Conditions for Clearing the DTC
|
B3205 00, B3210 00
Installing a compatible window motor for that specific make and model vehicle.
B3205 39, B3210 39, B3215 39, B3220 39
If the DTC is current, the appropriate window motor must be replaced before the DTC can be cleared.
B3205 42, B3210 42
The appropriate window motor must be replaced before the DTC can be cleared.
B3205 4B, B3210 4B
The appropriate window motor must be normalized before the DTC can be cleared.
Schematic Reference
Moveable Window Schematics
Connector End View Reference
Component Connector End Views
Description and Operation
Power Windows Description and Operation
Electrical Information Reference
Scan Tool Reference
Control Module References
for scan tool information
|
Circuit/System Verification
|
B3205 00, B3205 39, B3205 42, B3210 00, B3210 39, B3210 42, B3215 39, B3220 39
|
1.
|
Ignition ON, command the M74 window motor UP and DOWN with a scan tool. The M74 window motor should perform the UP and DOWN functions.
|
|
2.
|
|
Note
|
|
If the window performs the UP and DOWN functions, clear the DTC
|
Replace the M74 window motor with a M74 window motor compatible for that specific make and model vehicle.
|
B3205 4B, B3210 4B
|
1.
|
Ignition ON, starting with the window completely UP. Hold the appropriate switch down until the window is fully open. Continue holding the switch down for approximately 5 seconds after the window is completely open.
|
|
2.
|
Pull the power window switch up until the window is fully closed and continue holding the switch up for approximately 5 seconds after the window is completely closed.
|
|
3.
|
Command the window to express UP and express DOWN by pressing the window switch past the first detent and releasing and then pulling the window switch past the first detent and releasing. The window should perform the express UP and express DOWN functions.
|
|
4.
|
If the M74 window motor does not perform as specified and the DTC resets, replace the M74 window motor.
|
Perform the
Diagnostic Repair Verification
after completing the diagnostic procedure.
