PRE-RELEASE
DTC P0667, P0668, or P0669
| DTC P0667, P0668, or P0669 |
| Diagnostic Instructions |
| • |
Perform the
Diagnostic System Check - Vehicle
prior to using this diagnostic procedure.
|
|
| • |
Review
Strategy Based Diagnosis
for an overview of the diagnostic approach.
|
|
| • |
Diagnostic Procedure Instructions
provides an overview of each diagnostic category.
|
|
| DTC Descriptors |
DTC P0667
Control Module Temperature Sensor Performance
DTC P0668
Control Module Temperature Sensor Circuit Low Voltage
DTC P0669
Control Module Temperature Sensor Circuit High Voltage
| Circuit/System Description |
The transmission control module (TCM) temperature sensor is located inside of the control solenoid valve assembly, which has no serviceable components. The TCM temperature sensor provides the temperature of the TCM. This temperature reading is used in various shifting and diagnostic routines in the TCM software. This fault is handled inside the TCM and no external circuits are involved.
| Conditions for Running the DTC |
P0667
| • |
DTC P0101, P0102, P0103, P0106, P0107, P0108, P0171, P0172, P0174, P0175, P0201, P0202, P0203, P0204, P0205, P0206, P0207, P0208, P0300, P0301, P0302, P0303, P0304, P0305, P0306, P0307, P0308, P0401, P042E, P0658, P0667, P0668, P0669, P06AD, P06AE, P0712, P0713, P0716, P0717, P0722, P0723, P0962, P0963, P0966, P0967, P0970, P0971, P215C, P2720, P2721, P2729, or P2730 is not set.
|
|
| • |
Brake torque is not active.
|
|
| • |
The engine speed is 400 RPM or greater for 5 seconds.
|
|
| • |
The ignition voltage is 8.6 volts or greater.
|
|
| • |
The engine torque signal is valid.
|
|
| • |
The throttle position signal is valid.
|
|
P0668
| • |
DTC P0668 is not set.
|
|
| • |
The engine speed is 400 RPM or greater for 5 seconds.
|
|
| • |
The ignition voltage is 8.6 volts or greater.
|
|
P0669
| • |
DTC P0669, P0716, P0717, P0722, or P0723 is not set.
|
|
| • |
The engine speed is 400 RPM or greater for 5 seconds.
|
|
| • |
The ignition voltage is 8.6 volts or greater.
|
|
| Conditions for Setting the DTC |
P0667
| • |
The difference between the transmission fluid temperature (TFT) and TCM substrate temperature is greater than 20-50°C (36-90°F), depending on the average of the TFT, TCM substrate and TCM power up temperatures.
|
|
| • |
The difference between the TCM power up temperature and TCM substrate temperature is greater than 8-10°C (14-18°F) depending on the average of the TFT, TCM substrate and TCM power up temperatures.
|
|
| • |
The above conditions have to be met for 5 minutes within a 6 minute period.
|
|
P0668
The TCM temperature is -249°C (-416°F) or lower for 1 minute.P0669
The TCM temperature is 249°C (480°F) or greater for 1 minute.| Action Taken When the DTC Sets |
| • |
DTCs P0667, P0668, and P0669 are Type B DTCs.
|
|
| • |
The TCM defaults the TCM substrate temperature to the TCM power up temperature.
|
|
| Conditions for Clearing the DTC |
DTCs P0667, P0668, and P0669 are Type B DTCs.
| Diagnostic Aids |
The TCM temperature sensor is located inside of the control solenoid valve assembly and its output should resemble that of the TFT sensor output.
| Reference Information |
Connector End View Reference
| • |
Component Connector End Views
|
|
| • |
Inline Harness Connector End Views
|
|
Description and Operation
Electronic Component Description for control solenoid valve assembly
Electrical Information Reference
| • |
Circuit Testing
|
|
| • |
Connector Repairs
|
|
| • |
Testing for Intermittent Conditions and Poor Connections
|
|
| • |
Wiring Repairs
|
|
DTC Type Reference
Powertrain Diagnostic Trouble Code (DTC) Type Definitions
Scan Tool Reference
Control Module References for scan tool information
| Circuit/System Verification |
| 1. |
Engine idling at normal operating temperature, verify the scan tool TCM Temperature parameter is between -247 and +247°C (-412 and +477°F).
|
|
| 2. |
If not within the specified range, replace the Q8 control solenoid valve assembly. Refer to
Control Solenoid Valve and Transmission Control Module Assembly Replacement
.
|
|
| 3. |
Operate the vehicle at 64 km/h (40 mph) for 10 minutes. Monitor the TCM temperature and the transmission's fluid temperature parameters with a scan tool. The TCM temperature parameter must increase with more than 2°C (3.5°F). The parameters for TCM-temperature and transmission oil temperature must lie within 20°C (36°F) of each other.
|
|
| 4. |
If the TCM Temperature parameter does not increase by greater than 2°C (3.5°F) or the TCM Temperature and Transmission Fluid Temperature parameters are not within 20°C (36°F), then replace the Q8 control solenoid valve assembly.
|
|
| 5. |
After you complete the steps described above, check that the diagnostic trouble code does not return by driving the vehicle according to the conditions for running diagnostic trouble codes (DTC). You can also drive the vehicle according to the conditions you have seen in Freeze Frame/Failure records. If the vehicle passes the Circuit/System Verification procedure, refer to
Testing for Intermittent Conditions and Poor Connections
.
|
|
| Repair Instructions |
| Note | ||
| • |
Perform the
Resetting of the transmission's adaption
after all transmission repairs.
|
|
| • |
Before replacing the TCM, perform the
Control Solenoid Valve and Transmission Control Module Assembly Inspection
.
|
|
Perform the Diagnostic Repair Verification after completing the diagnostic procedure.
Control Module References for control solenoid valve assembly replacement, setup, and programming
